View M38869FC-XXXHP_4458301.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

To all our customers
Regarding the change of names mentioned in the document, such as Mitsubishi Electric and Mitsubishi XX, to Renesas Technology Corp.
The semiconductor operations of Hitachi and Mitsubishi Electric were transferred to Renesas Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog and discrete devices, and memory chips other than DRAMs (flash memory, SRAMs etc.) Accordingly, although Mitsubishi Electric, Mitsubishi Electric Corporation, Mitsubishi Semiconductors, and other Mitsubishi brand names are mentioned in the document, these names have in fact all been changed to Renesas Technology Corp. Thank you for your understanding. Except for our corporate trademark, logo and corporate statement, no changes whatsoever have been made to the contents of the document, and these changes do not constitute any alteration to the contents of the document itself. Note : Mitsubishi Electric will continue the business operations of high frequency & optical devices and power devices.
Renesas Technology Corp. Customer Support Dept. April 1, 2003
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
DESCRIPTION
The 3886 group is the 8-bit microcomputer based on the 740 family core technology. The 3886 group is designed for controlling systems that require analog signal processing and include two serial I/O functions, A-D converters, D-A converters, system data bus interface function, watchdog timer, and comparator circuit. The multi-master I2C bus interface can be added by option.
qPower dissipation In high-speed mode .......................................................... 40 mW (at 10 MHz oscillation frequency, at 5 V power source voltage) In low-speed mode ............................................................ 60 W (at 32 kHz oscillation frequency, at 3 V power source voltage) qMemory expansion possible (only for M38867M8A/E8A) qOperating temperature range .................................... -20 to 85C qSupply voltage ................................................. VCC = 5 V 10 % qProgram/Erase voltage ............................... VPP = 11.7 to 12.6 V qProgramming method ...................... Programming in unit of byte qErasing method Batch erasing ........................................ Parallel/Serial I/O mode Block erasing .................................... CPU reprogramming mode qProgram/Erase control by software command qNumber of times for programming/erasing ............................ 100 qOperating temperature range (at programming/erasing) ..................................................................... Normal temperature
FEATURES
qBasic machine-language instructions ...................................... 71 qMinimum instruction execution time .................................. 0.4 s (at 10 MHz oscillation frequency) qMemory size ROM ................................................................. 32K to 60K bytes RAM ............................................................... 1024 to 2048 bytes qProgrammable input/output ports ............................................ 72 qSoftware pull-up resistors ................................................. Built-in qInterrupts ................................................. 21 sources, 16 vectors (Included key input interrupt) qTimers ............................................................................. 8-bit ! 4 qSerial I/O1 .................... 8-bit ! 1(UART or Clock-synchronized) qSerial I/O2 ................................... 8-bit ! 1(Clock-synchronized) qPWM output circuit ....................................................... 14-bit ! 2 qBus interface .................................................................... 2 bytes qI2C bus interface (option) ............................................. 1 channel qA-D converter ............................................... 10-bit ! 8 channels qD-A converter ................................................. 8-bit ! 2 channels qComparator circuit ...................................................... 8 channels qWatchdog timer ............................................................ 16-bit ! 1 qClock generating circuit ..................................... Built-in 2 circuits (connect to external ceramic resonator or quartz-crystal oscillator) qPower source voltage In high-speed mode .................................................. 4.0 to 5.5 V (at 10 MHz oscillation frequency) In middle-speed mode ........................................... 2.7 to 5.5 V(*) (at 10 MHz oscillation frequency) In low-speed mode ............................................... 2.7 to 5.5 V (*) (at 32 kHz oscillation frequency) (*: 4.0 to 5.5 V for Flash memory version)
sNotes 1. The flash memory version cannot be used for application embedded in the MCU card. 2. Power source voltage Vcc of the flash memory version is 4.0 to 5.5 V.
APPLICATION
Household product, consumer electronics, communications, note book PC, etc.
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PIN CONFIGURATION (TOP VIEW)
P32/ONW P33/RESETOUT P34/ P35/SYNC P36/WR P37/RD P00/P3REF/AD0 P01/AD1 P02/AD2 P03/AD3 P04/AD4 P05/AD5 P06/AD6 P07/AD7 P10/AD8 P11/AD9 P12/AD10 P13/AD11 P14/AD12 P15/AD13
42 41 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43
P31/PWM10 P30/PWM00 P87/DQ7 P86/DQ6 P85/DQ5 P84/DQ4 P83/DQ3 P82/DQ2 P81/DQ1 P80/DQ0 VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3 P62/AN2 P61/AN1
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
1
M38867M8A-XXXHP M38867E8AHP
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
20
P16/AD14 P17/AD15 P20/DB0 P21/DB1 P22/DB2 P23/DB3 P24/DB4 P25/DB5 P26/DB6 P27/DB7 VSS XOUT XIN P40/XCOUT P41/XCIN RESET VPP CNVSS P42/INT0/OBF00 P43/INT1/OBF01 P44/RXD
11 12 13
15 16
17 18
7 8 9 10
14
P60/AN0 P77/SCL P76/SDA P75/INT41 P74/INT31 P73/SRDY2/INT21 P72/SCLK2 P71/SOUT2 P70/SIN2 P57/DA2/PWM11 P56/DA1/PWM01 P55/CNTR1 P54/CNTR0 P53/INT40/W P52/INT30/R P51/INT20/S0 P50/A0 P47/SRDY1/S1 P46/SCLK1/OBF10 P45/TXD
19
2 3
4
5
6
: PROM version Note: The pin number and the position of the function pin may change by the kind of package.
Package type : 80P6Q-A
Fig. 1 M38867M8A-XXXHP, M38867E8AHP pin configuration
PIN CONFIGURATION (TOP VIEW)
P30/PWM00 P31/PWM10 P32/ONW P33/RESETOUT P34/ P35/SYNC P36/WR P37/RD P00/P3REF/AD0 P01/AD1 P02/AD2 P03/AD3 P04/AD4 P05/AD5 P06/AD6 P07/AD7 P10/AD8 P11/AD9 P12/AD10 P13/AD11 P14/AD12 P15/AD13 P16/AD14 P17/AD15
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48
P87/DQ7 P86/DQ6 P85/DQ5 P84/DQ4 P83/DQ3 P82/DQ2 P81/DQ1 P80/DQ0 VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3
69 70 71 72 73 74 75 76 77 78 79 80
M38867E8AFS
65 66 67 68
47 46 45 44 43 42 41
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25
P20/DB0 P21/DB1 P22/DB2 P23/DB3 P24/DB4 P25/DB5 P26/DB6 P27/DB7 VSS XOUT XIN P40/XCOUT P41/XCIN RESET VPP CNVSS P42/INT0/OBF00
5 6 7 8 9 10 11 12 13 14 15 16 17
P62/AN2 P61/AN1 P60/AN0 P77/SCL P76/SDA P75/INT41 P74/INT31 P73/SRDY2/INT21 P72/SCLK2 P71/SOUT2 P70/SIN2 P57/DA2/PWM11 P56/DA1/PWM01 P55/CNTR1 P54/CNTR0 P53/INT40/W P52/INT30/R P51/INT20/S0 P50/A0 P47/SRDY1/S1 P46/SCLK1/OBF10 P45/TXD P44/RXD P43/INT1/OBF01
18 19 20 21 22 23 24
1 2 3 4
Package type : 80D0
Fig. 2 M38867E8AFS pin configuration
Note: The pin number and the position of the function pin may change by the kind of package.
2
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PIN CONFIGURATION (TOP VIEW)
P32 P33 P34 P35 P36 P37 P00/P3REF P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13 P14 P15
46 45 44 43 42 60 59 58 50 49 48 47 57 56 55 54 53 52 51 41
40 39 38 37 36 35 34 33
P31/PWM10 P30/PWM00 P87/DQ7 P86/DQ6 P85/DQ5 P84/DQ4 P83/DQ3 P82/DQ2 P81/DQ1 P80/DQ0 VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3 P62/AN2 P61/AN1
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
M38869MFA-XXXGP/HP M38869FFAGP/HP
32 31 30 29 28 27 26 25 24 23 22 21
P16 P17 P20 P21 P22 P23 P24 P25 P26 P27 VSS XOUT XIN P40/XCOUT P41/XCIN RESET CNVSS VPP P42/INT0/OBF00 P43/INT1/OBF01 P44/RXD
12
13
14
15
16
17
11
P60/AN0 P77/SCL P76/SDA P75/INT41 P74/INT31 P73/SRDY2/INT21 P72/SCLK2 P71/SOUT2 P70/SIN2 P57/DA2/PWM11 P56/DA1/PWM01 P55/CNTR1 P54/CNTR0 P53/INT40/W P52/INT30/R P51/INT20/S0 P50/A0 P47/SRDY1/S1 P46/SCLK1/OBF10 P45/TXD
9 10
18
19
20
1
2
3
7 8
4 5
6
: Flash memory version Note: The pin number and the position of the function pin may change by the kind of package.
Package type : 80P6S-A/80P6Q-A
Fig. 3 M38869MFA-XXXGP/HP, M38869FFAGP/HP pin configuration
3
4
Reset input VSS VCC RESET
25 24 71 30
FUNCTIONAL BLOCK DIAGRAM (Package : 80P6Q-A, 80P6S-A)
Main-clock input XIN CNVSS
Main-clock output XOUT
28
29
Sub-clock Sub-clock input output
FUNCTIONAL BLOCK
Fig. 4 Functional block diagram
CPU
XCIN
XCOUT
Clock generating circuit
RAM ROM
X
Prescaler 12(8)
A Timer 2( 8 ) Timer X( 8 ) Timer Y( 8 )
Timer 1( 8 )
Y
Prescaler X(8)
S PC H PS
CNTR0 CNTR1
PCL
Prescaler Y(8)
Watchdog timer
Reset
IC
D-A converter 2 (8) D-A converter 1(8)
2
SI/O2(8) SI/O1(8) Comparator
A-D converter (10)
PWM0(14)
PWM1(14)
SCL SDA XCOUT XCIN
Bus interface INT0, INT1
DQ0
INT20, INT30, INT40
Key-on wake-up
PWM00, PWM01
PWM10, PWM11
to
DQ7
INT21, INT31, INT41
P8(8) P6(8) P5(8) P4(8)
P7(8)
P3(8)
P2(8)
P1(8)
P0(8)
P3REF
63 64 65 66 67 68 69 70
23456789 10 11 12 13 14 15 16 17
72 73 74 75 76 77 78 79 80 1
18 19 20 21 22 23 26 27
55 56 57 58 59 60 61 62
31 32 33 34 35 36 37 38
39 40 41 42 43 44 45 46
47 48 49 50 51 52 53 54
I/O port P8
I/O port P7
I/O port P6 I/O port P5
I/O port P4
I/O port P3
I/O port P2
I/O port P1
I/O port P0
VREF
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
3886 Group
AVSS
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PIN DESCRIPTION
Table 1 Pin description (1) Pin VCC, VSS Name Power source Functions *Apply voltage of 2.7 V - 5.5 V to Vcc, and 0 V to Vss. *In the flash memory version, apply voltage of 4.0 V - 5.5 V to Vcc, and 0 V to Vss *This pin controls the operation mode of the chip. *Normally connected to VSS. CNVSS CNVSS input *If this pin is connected to Vcc, the internal ROM is inhibited and an external memory is accessed. *In the flash memory version, connected to VSS. *In the EPROM version or the flash memory version, this pin functions as the VPP power source input pin. VREF AVSS RESET XIN XOUT Reference voltage Analog power source Reset input Clock input Clock output *Reference voltage input pin for A-D and D-A converters. *Analog power source input pin for A-D and D-A converters. *Connect to VSS. *Reset input pin for active "L". *Input and output pins for the clock generating circuit. *Connect a ceramic resonator or quartz-crystal oscillator between the XIN and XOUT pins to set the oscillation frequency. *When an external clock is used, connect the clock source to the XIN pin and leave the XOUT pin open. *8-bit CMOS I/O port. *Comparator reference power source *I/O direction register allows each pin to be individually input pin programmed as either input or output. *When the external memory is used, these pins are used as the address bus. *CMOS compatible input level. *CMOS 3-state output structure or N-channel open-drain output structure. *8-bit CMOS I/O port. *I/O direction register allows each pin to be individually programmed as either input or output. P10-P17 I/O port P1 *When the external memory is used, these pins are used as the address bus. *CMOS compatible input level. *CMOS 3-state output structure or N-channel open-drain output structure. *8-bit CMOS I/O port. *I/O direction register allows each pin to be individually programmed as either input or output. P20-P27 I/O port P2 *When the external memory is used, these pins are used as the data bus. *CMOS compatible input level. *CMOS 3-state output structure. *P24 to P27 (4 bits) are enabled to output large current for LED drive (only in single-chip mode). *8-bit CMOS I/O port. *I/O direction register allows each pin to be individually programmed as either input or output. *When the external memory is used, these pins are used as the control bus. I/O port P3 *CMOS compatible input level. *CMOS 3-state output structure. P32-P37 *These pins function as key-on wake-up and comparator input. *These pins are enabled to control pull-up. *Key-on wake-up input pin *Comparator input pin *PWM output pin
Function except a port function
P00/P3REF I/O port P0 P01-P07
P30/PWM00 P31/PWM10
*Key-on wake-up input pin *Comparator input pin
5
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 2 Pin description (2) Pin Name Functions *8-bit I/O port with the same function as port P0. P40/XCOUT P41/XCIN P40, P41 : CMOS input level P42-P46 : CMOS compatible input level or TTL input level P47 : CMOS compatible input level or TTL input level in the bus interface function I/O port P4 P40, P41, P47 : CMOS 3-state output structure P44/RxD P45/TxD P46/SCLK1 /OBF10 P47/SRDY1 /S1 P50/A0 P51/INT20 /S0 P52/INT30 /R P53/INT40 /W P54/CNTR0 P55/CNTR1 P56/DA1 /PWM01 P57/DA2 /PWM11 P60/AN0- P67/AN7 P70/SIN2 P71/SOUT2 P72/SCLK2 P73/SRDY2 /INT21 P74/INT31 P75/INT41 P76/SDA P77/SCL I/O port P7 I/O port P6 *8-bit I/O port with the same function as port P0. *CMOS compatible input level. *CMOS 3-state output structure. *8-bit I/O port with the same function as port P0. P70-P75 : CMOS compatible input level or TTL input level P76, P77 : CMOS compatible input level or SMBUS input level in the I2C-BUS interface function, N-channel open-drain output structure *Regardless of input or output port, P70 to P75 can be input every pin level. *8-bit I/O port with the same function as port P0. P80/DQ0- P87/DQ7 *CMOS compatible input level. I/O port P8 *CMOS 3-state output structure. *CMOS compatible input level or TTL input level in the bus interface function. *Bus interface function pin *Serial I/O2 function pin *Serial I/O2 function pin *Interrupt input pin *Interrupt input pin *I2C-BUS interface function pin P42-P46 : CMOS 3-state output structure or Nchannel open-drain output structure *Regardless of input or output port, P42 to P46 can be input every pin level. *When P42 and P43 are used as output port, the function which makes P42 and P43 clear to "0" when the host CPU reads the output data bus buffer 0 can be added. *8-bit I/O port with the same function as port P0. *CMOS compatible input level. *CMOS 3-state output structure. *P50 to P53 can be switched between CMOS compatible input level or TTL input level in the bus interface function. I/O port P5 *Timer X, timer Y function pins *Interrupt input pins *Bus interface function pins *Serial I/O1 function pins *Interrupt input pins *Bus interface function pins
Function except a port function *Sub-clock generating circuit I/O pins (Connect a resonator.)
P42/INT0 /OBF00 P43/INT1 /OBF01
*Serial I/O1 function pins *Bus interface function pins *Bus interface function pins
*D-A converter output pin *PWM output pin
*A-D converter output pin
6
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PART NUMBERING
Product name
M3886
7
M
8 A-
XXX
HP
Package type HP : 80P6Q-A GP : 80P6S-A FS : 80D0
ROM number Omitted in the one time PROM version shipped in blank, the EPROM version and the flash memory version.
A- : High-speed version - is omitted in the One Time PROM version shipped in blank, the EPROM version and the flash memory version.
ROM/PROM size 1 : 4096 bytes 9: 36864 bytes 2 : 8192 bytes A : 40960 bytes B : 45056 bytes 3 : 12288 bytes C: 49152 bytes 4 : 16384 bytes D: 53248 bytes 5 : 20480 bytes E : 57344 bytes 6 : 24576 bytes F : 61440 bytes 7 : 28672 bytes 8 : 32768 bytes The first 128 bytes and the last 2 bytes of ROM are reserved areas ; they cannot be used. However, they can be programmed or erased in the EPROM version and the flash memory version, so that the users can use them. Memory type M : Mask ROM version E : EPROM or One Time PROM version F : Flash memory version
RAM size 0 : 192 bytes 1 : 256 bytes 2 : 384 bytes 3 : 512 bytes 4 : 640 bytes
5 : 768 bytes 6 : 896 bytes 7 : 1024 bytes 8 : 1536 bytes 9 : 2048 bytes
Fig. 5 Part numbering
7
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GROUP EXPANSION
Mitsubishi plans to expand the 3886 group as follows.
Packages
80P6Q-A .................................. 0.5 mm-pitch plastic molded LQFP 80P6S-A ................................... 0.65mm pitch plastic molded QFP 80D0 ....................... 0.8 mm-pitch ceramic LCC (EPROM version) The pin number and the position of the function pin may change by the kind of package.
Memory Type
Support for mask ROM, One Time PROM, EPROM and flash memory version.
Memory Size
ROM size ........................................................... 32 K to 60 K bytes RAM size .......................................................... 1024 to 2048 bytes
Memory Expansion
ROM size (bytes) ROM external 60K : Mass production
M38869FFA/MFA
48K
M38869MCA
32K
M38867E8A/M8A
M38869M8A
28K
24K
20K
16K
12K
8K
384
512
640
768
896
1024
1152
1280
1408
1536
2048
3072
4032
RAM size (bytes)
Fig. 6 Memory expansion plan Currently products are listed below. Table 3 Support products Product name M38867M8A-XXXHP M38867E8A-XXXHP M38867E8AHP M38867E8AFS M38869M8A-XXXHP M38869M8A-XXXGP M38869MCA-XXXHP M38869MCA-XXXGP M38869MFA-XXXHP M38869MFA-XXXGP M38869FFAHP M38869FFAGP (P) ROM size (bytes) ROM size for User in ( ) RAM size (bytes) Package Remarks Mask ROM version One Time PROM version One Time PROM version (blank) EPROM version As of Jan. 2000
1024 32768 (32638)
80P6Q-A 80D0 80P6Q-A 80P6S-A 80P6Q-A 80P6S-A 80P6Q-A 80P6S-A 80P6Q-A 80P6S-A
49152 (19022) 2048
Mask ROM version
61440 (61310)
Flash memory version
8
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
FUNCTIONAL DESCRIPTION CENTRAL PROCESSING UNIT (CPU)
The 3886 group uses the standard 740 Family instruction set. Refer to the table of 740 Family addressing modes and machine instructions or the 740 Family Software Manual for details on the instruction set. Machine-resident 740 Family instructions are as follows: The FST and SLW instructions cannot be used. The STP, WIT, MUL, and DIV instructions can be used.
[CPU Mode Register (CPUM)] 003B16
The CPU mode register contains the stack page selection bit, the processor mode bits specifying the chip operation mode, etc. The CPU mode register is allocated at address 003B16.
b7
b0
CPU mode register
(CPUM : address 003B16)
Processor mode bits b1 b0 0 0 : Single-chip mode 0 1 : Memory expansion mode (Note) 1 0 : Microprocessor mode (Note) 1 1 : Not available Stack page selection bit 0 : 0 page 1 : 1 page Reserved (Do not write "0" to this bit when using XCIN-XCOUT oscillation function.) Port XC switch bit 0 : I/O port function (stop oscillating) 1 : XCIN-XCOUT oscillating function Main clock (XIN-XOUT) stop bit 0 : Oscillating 1 : Stopped Main clock division ratio selection bits b7 b6 0 0 : = f(XIN)/2 (high-speed mode) 0 1 : = f(XIN)/8 (middle-speed mode) 1 0 : = f(XCIN)/2 (low-speed mode) 1 1 : Not available Note: This mode is not available for M38869M8A/MCA/MFA and the flash memory version.
Fig. 7 Structure of CPU mode register
9
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MEMORY Special Function Register (SFR) Area
The Special Function Register area in the zero page contains control registers such as I/O ports and timers.
Interrupt Vector Area
The interrupt vector area contains reset and interrupt vectors.
Zero Page
Access to this area with only 2 bytes is possible in the zero page addressing mode.
RAM
RAM is used for data storage and for stack area of subroutine calls and interrupts.
Special Page
Access to this area with only 2 bytes is possible in the special page addressing mode.
ROM
The first 128 bytes and the last 2 bytes of ROM are reserved for device testing and the rest is user area for storing programs. Program/Erase of the reserved ROM area is possible in the EPROM version and the flash memory version
RAM area
RAM size (bytes) Address XXXX16
000016 SFR area 004016 010016 Zero page
192 256 384 512 640 768 896 1024 1536 2048
00FF16 013F16 01BF16 023F16 02BF16 033F16 03BF16 043F16 063F16 083F16
RAM
XXXX16 Not used 0FFE16 0FFF16 SFR area (Note 1)
ROM area
ROM size (bytes) Address YYYY16 Address ZZZZ16
YYYY16 Reserved ROM area (Note 2) (128 bytes) ZZZZ16
4096 8192 12288 16384 20480 24576 28672 32768 36864 40960 45056 49152 53248 57344 61440
F00016 E00016 D00016 C00016 B00016 A00016 900016 800016 700016 600016 500016 400016 300016 200016 100016
F08016 E08016 D08016 C08016 B08016 A08016 908016 808016 708016 608016 508016 408016 308016 208016 108016
ROM FF0016 FFDC16 Interrupt vector area FFFE16 FFFF16 Reserved ROM area (Note 2) Special page
Notes 1: This area is SFR in M38869FFA.
This area is Reserved in M38869MFA/MCA/M8A. This area is not used in M38867M8A/E8A. 2: This area is usable in EPROM version and flash memory version.
Fig. 8 Memory map diagram
10
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
000016 000116 000216 000316 000416 000516 000616 000716 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16 001016 001116 001216 001316 001416 001516 001616 001716 001816 001916 001A16 001B16 001C16 001D16 001E16 001F16
Port P0 (P0) Port P0 direction register (P0D) Port P1 (P1) Port P1 direction register (P1D) Port P2 (P2) Port P2 direction register (P2D) Port P3 (P3) Port P3 direction register (P3D) Port P4 (P4) Port P4 direction register (P4D) Port P5 (P5) Port P5 direction register (P5D) Port P6 (P6) Port P6 direction register (P6D) Port P7 (P7) Port P7 direction register (P7D) Port P8 (P8)/Port P4 input register (P4I) Port P8 direction register (P8D)/Port P7 input register (P7I) I2C data shift register (S0) I2C address register (S0D) I2C status register (S1) I2C control register (S1D) I2C clock control register (S2) I2C start/stop condition control register (S2D) Transmit/Receive buffer register (TB/RB) Serial I/O1 status register (SIO1STS) Serial I/O1 control register (SIO1CON) UART control register (UARTCON) Baud rate generator (BRG) Serial I/O2 control register (SIO2CON) Watchdog timer control register (WDTCON) Serial I/O2 register (SIO2)
002016 002116 002216 002316 002416 002516 002616 002716 002816 002916 002A16 002B16 002C16 002D16 002E16 002F16 003016 003116 003216 003316 003416 003516 003616 003716 003816 003916 003A16 003B16 003C16 003D16 003E16 003F16
Prescaler 12 (PRE12) Timer 1 (T1) Timer 2 (T2) Timer XY mode register (TM) Prescaler X (PREX) Timer X (TX) Prescaler Y (PREY) Timer Y (TY) Data bas buffer register 0 (DBB0) Data bas buffer status register 0 (DBBSTS0) Data bas buffer control register (DBBCON) Data bas buffer register 1 (DBB1) Data bas buffer status register 1 (DBBSTS1) Comparator data register (CMPD) Port control register 1 (PCTL1) Port control register 2 (PCTL2) PWM0H register (PWM0H) PWM0L register (PWM0L) PWM1H register (PWM1H) PWM1L register (PWM1L) AD/DA control register (ADCON) A-D conversion register 1 (AD1) D-A1 conversion register (DA1) D-A2 conversion register (DA2) A-D conversion register 2 (AD2) Interrupt source selection register (INTSEL) Interrupt edge selection register (INTEDGE) CPU mode register (CPUM) Interrupt request register 1 (IREQ1) Interrupt request register 2 (IREQ2) Interrupt control register 1 (ICON1) Interrupt control register 2 (ICON2) (Note) (Note)
0FFE16 0FFF16
Flash memory control register (FCON) Flash command register (FCMD) Note: Flash memory version only
Fig. 9 Memory map of special function register (SFR)
11
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
I/O PORTS
The I/O ports have direction registers which determine the input/ output direction of each individual pin. Each bit in a direction register corresponds to one pin, and each pin can be set to be input port or output port. When "0" is written to the bit corresponding to a pin, that pin becomes an input pin. When "1" is written to that bit, that pin becomes an output pin. If data is read from a pin which is set to output, the value of the port output latch is read, not the value of the pin itself. Pins set to input are floating. If a pin set to input is written to, only the port Table 4 I/O port function (1) Pin Name Input/Output I/O Structure
output latch is written to and the pin remains floating. When the P8 function select bit of the port control register 2 (address 002F16) is set to "1", read from address 001016 becomes the port P4 input register, and read from address 001116 becomes the port P7 input register. As the particular function, value of P42 to P46 pins and P70 to P75 pins can be read regardless of setting direction registers, by reading the port P4 input register (address 001016) or the port P7 input register (address 001116) respectively.
Non-Port Function Address low-order byte output Analog comparator power source input pin Address low-order byte output Address high-order byte output Data bus I/O Control signal I/O PWM output Key-on wake up input Comparator input Control signal I/O Key-on wake up input Comparator input Sub-clock generating circuit
Related SFRs CPU mode register Port control register 1 Serial I/O2 control register
Ref.No. (1)
P00/P3REF Port P0 P01-P07 P10-P17 P20-P27 P30/PWM00 P31/PWM10 Port P3 P32-P37 P40/XCOUT P41/XCIN P42/INT0/ OBF00 P43/INT1/ OBF01 P44/RXD Input/output, individual bits Port P1 Port P2
CMOS compatible input level CMOS 3-state output or N-channel opendrain output
CPU mode register Port control register 1 CPU mode register CPU mode register Port control register 1 AD/DA control register CPU mode register Port control register 1 CPU mode register Interrupt edge selection register Port control register 2 Serial I/O1 control register Port control register 2 Serial I/O1 control register UART control register Port control register 2 Serial I/O1 control register Data bus buffer control register Port control register 2
(2)
(3) (4) (5)
CMOS compatible input level CMOS 3-state output
(6) (7) (8) (9) (10)
External interrupt input Bus interface function I/O CMOS compatible input level or TTL input level CMOS 3-state output or N-channel opendrain output Serial I/O1 function input Serial I/O1 function output
(11)
P45/TXD Port P4
(12)
P46/SCLK1 /OBF10
Serial I/O1 function I/O Bus interface function output CMOS compatible input level CMOS 3-state output (when selecting bus interface function) CMOS compatible input level or TTL input level
(13)
P47/SRDY1 /S1
Serial I/O1 function output Bus interface function input
Serial I/O1 control register Data bus buffer control register
(14)
12
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 5 I/O port function (2) Pin P50/A0 P51/INT20 /S0 P52/INT30 /R P53/INT40 /W P54/CNTR0 P55/CNTR1 P56/DA1/ PWM01 P57/DA2/ PWM11 P60/AN0- P67/AN7 P70/SIN2 P71/SOUT2 P72/SCLK2 P73/SRDY2/ INT21 P74/INT31 P75/INT41 Port P6 Name Input/Output I/O Format CMOS compatible input level CMOS 3-state output (when selecting bus interface function) CMOS compatible input level or TTL input level Non-Port Function Bus interface function input Related SFRs Data bus buffer control register Interrupt edge selection register Data bus buffer control register Ref.No. (15)
Port P5
External interrupt input Bus interface function input
(16)
Timer X, timer Y function I/O CMOS compatible input level CMOS 3-state output D-A converter output PWM output
Timer XY mode register AD/DA control register UART control register
(17)
(18) (19) (20) (21) (22) (23)
A-D converter input
AD/DA control register Serial I/O2 control register Port control register 2 Serial I/O2 control register Port control register 2 Interrupt edge selection register Port control register 2
Input/output, individual bits
Serial I/O2 function I/O CMOS compatible input level or TTL input level N-channel open-drain output Serial I/O2 function output Bus interface function input External interrupt input CMOS compatible input level N-channel open-drain output (when selecting I2CBUS interface function) CMOS compatible input level or SMBUS input level CMOS compatible input level CMOS 3-state output (when selecting bus interface function) CMOS compatible input level or TTL input level
(24)
Port P7
(25)
P76/SDA P77/SCL
I2C-BUS interface function I/O
I2C control register
(26) (27)
P80/DQ0- P87/DQ7
Port P8
Bus interface function I/O
Data bus buffer control register
(28)
Notes1: For details of the functions of ports P0 to P3 in modes other than single-chip mode, and how to use double-function ports as function I/O ports, refer to the applicable sections. 2: Make sure that the input level at each pin is either 0 V or VCC during execution of the STP instruction. When an input level is at an intermediate potential, a current will flow from VCC to VSS through the input-stage gate.
13
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(1) Port P00
P00-P03 output structure selection bit Direction register
(2) Ports P01-P07,P1
P00-P03, P04-P07, P10-P13, P14-P17 output structure selection bits Direction register Data bus Port latch
Data bus
Port latch
Comparator reference power source input Comparator reference input pin select bit
(3) Port P2
Direction register
(4) Port P30
PWM0 output pin selection bit PWM0 enable bit Direction register Data bus Port latch
P30-P33 pull-up control bit
Data bus
Port latch
PWM00 output
Comparator input Key-on wake-up
(5) Port P31
PWM1 output pin selection bit PWM1 enable bit Direction register Data bus Port latch
P30-P33 pull-up control bit
(6) Ports P32-P37
P30-P33, P34-P37 pull-up control bit
Direction register
Data bus
Port latch
PWM10 output
Comparator input Key-on wake-up Comparator input Key-on wake-up
(7) Port P40
Port XC switch bit Direction register
(8) Port P41
Port XC switch bit Direction register
Data bus
Port latch
Data bus
Port latch
Oscillator Port P41 Port XC switch bit Sub-clock generating circuit input
Fig. 10 Port block diagram (1)
14
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(9) Port P42
P4 output structure selection bit OBF00 output enable bit Direction register Data bus
(10) Port P43
P4 output structure selection bit OBF01 output enable bit Direction register
Port latch
Data bus
Port latch
T1 T2
T1 T2
OBF00 output INT0 interrupt input
OBF01 output INT1 interrupt input
(11) Port P44
P4 output structure selection bit Serial I/O1 enable bit Receive enable bit Direction register
(12) Port P45
P45/TXD P-channel output disable bit Serial I/O1 enable bit Transmit enable bit Direction register
Data bus Data bus Port latch
Port latch
T1 T1 T2 T2
Serial I/O1 output Serial I/O1 input
(13) Port P46
Serial I/O1 P4 output structure selection bit synchronous clock selection bit
(14) Port P47
Serial I/O1 mode selection bit
Serial I/O1 enable bit
Serial I/O1 mode selection bit
Serial I/O1 enable bit
OBF10 output enable bit
Direction register
Serial I/O1 enable bit SRDY1 output enable bit Data bus buffer function selection bit Direction register
Data bus
Port latch
Data bus
Port latch
T1 T2
Serial I/O1 ready output S1 input
T3 Data bus buffer function selection bit
Serial I/O1 clock output OBF10 output Serial I/O1 external clock input
(15) Port P50
Data bus buffer enable bit Direction register
(16) Ports P51,P52,P53
Data bus buffer enable bit Direction register
Data bus
Port latch
Data bus
Port latch
T3 A0 input Data bus buffer enable bit INT20, INT30, INT40 interrupt input T3 S0,R,W input Data bus buffer enable bit
T1. The input level can be switched between CMOS compatible input level and TTL level by the P4 input level selection bit of the port control register 2 (address 002F16). T2. The input level can be switched between CMOS compatible input level and TTL level by the P4 input level selection bit of the port control register 2 (address 002F16). The port P8 and port P4 input register can be switched by the P8 function selection bit of the port control register 2 (address 002F16). T3. The input level can be switched between CMOS compatible input level and TTL level by the input level selection bit of the data bus buffer control register (address 002A16).
Fig. 11 Port block diagram (2)
15
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(17) Ports P54,P55
Direction register
(18) Port P56
PWM0 output pin selection bit PWM0 enable bit Direction register
Data bus
Port latch Data bus
Port latch
Pulse output mode Timer output CNTR0,CNTR1 interrupt input PWM01 output D-A converter output D-A1 output enable bit
(19) Port P57
PWM1 output pin selection bit PWM1 enable bit Direction register
(20) Port P6
Direction register
Data bus Data bus Port latch
Port latch
A-D converter input Analog input pin selection bit PWM11 output D-A converter output D-A2 output enable bit
(21) Port P70
Direction register
(22) Port P71
Serial IO/2 transmit completion signal Serial I/O2 port selection bit Direction register
Data bus
Port latch Data bus
T4 T5 T4
Port latch
Serial I/O2 input
T5
Serial I/O2 output
(23) Port P72
Serial I/O2 synchronization clock selection bit Serial I/O2 port selection bit Direction register
(24) Port P73
SRDY2 output enable bit Direction register
Data bus Data bus Port latch
Port latch
T4 T4 T5 T5
Serial I/O2 ready output Serial I/O2 external clock input INT21 interrupt input
Serial I/O2 clock output
T4. The input level can be switched between CMOS compatible input level and TTL level by the P7 input level selection bit of the port control register 2 (address 002F16). T5. The input level can be switched between CMOS compatible input level and TTL level by the P7 input level selection bit of the port control register 2 (address 002F16). The port P8 direction register and port P7 input register can be switched by the P8 function selection bit of the port control register 2 (address 002F16).
Fig. 12 Port block diagram (3)
16
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(25) Ports P74,P75
Direction register
(26) Port P76
I2C-BUS interface enable bit Direction register
Data bus
Port latch Data bus
T4 T5
Port latch
INT31,INT41 interrupt input
SDA output SDA input
T6
(27) Port P77
I2C-BUS interface enable bit Direction register Data bus
(28) Port P8
S0 S1 R Data bus buffer enable bit Direction register
Port latch
Data bus
Port latch
Output buffer 0
SCL output SCL input
T6
Status register 0
Output buffer 1 Status register 1
T3 Input buffer 0 T3 Input buffer 1
T6. The input level can be switched between CMOS compatible input level and SMBUS level by the I2C-BUS interface pin input selection bit of the I2C control register (address 001516).
Fig. 13 Port block diagram (4)
17
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
b0 Port control register 1 (PCTL1: address 002E16) P00-P03 output structure selection bit 0: CMOS 1: N-channel open-drain P04-P07 output structure selection bit 0: CMOS 1: N-channel open-drain P10-P13 output structure selection bit 0: CMOS 1: N-channel open-drain P14-P17 output structure selection bit 0: CMOS 1: N-channel open-drain P30-P33 pull-up control bit 0: No pull-up 1: Pull-up P34-P37 pull-up control bit 0: No pull-up 1: Pull-up PWM0 enable bit 0: PWM0 output disabled 1: PWM0 output enabled PWM1 enable bit 0: PWM1 output disabled 1: PWM1 output enabled
b7
b0 Port control register 2 (PCTL2: address 002F16) P4 input level selection bit (P42-P46) 0: CMOS level input 1: TTL level input P7 input level selection bit (P70-P75) 0: CMOS level input 1: TTL level input P4 output structure selection bit (P42, P43, P44, P46) 0: CMOS 1: N-channel open-drain P8 function selection bit 0: Port P8/Port P8 direction register 1: Port P4 input register/Port P7 input register INT2, INT3, INT4 interrupt switch bit 0: INT20, INT30, INT40 interrupt 1: INT21, INT31, INT41 interrupt Timer Y count source selection bit 0: f(XIN)/16 (f(XCIN)/16 in low-speed mode) 1: f(XCIN) Oscillation stabilizing time set after STP instruction released bit 0: Automatic set "0116" to timer 1 and "FF16" to prescaler 12 1: No automatic set Port output P42/P43 clear function selection bit 0: Only software clear 1: Software clear and output data bus buffer 0 reading (system bus side)
Fig. 14 Structure of port I/O related register
18
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
INTERRUPTS
Interrupts occur by 16 sources among 21 sources: nine external, eleven internal, and one software.
Interrupt Source Selection
Any of the following interrupt sources can be selected by the interrupt source selection register (address 003916). 1. INT0 or Input buffer full 2. INT1 or Output buffer empty 3. Serial I/O1 transmission or SCLSDA 4. CNTR0 or SCLSDA 5. Serial I/O2 or I2C 6. INT2 or I2C 7. CNTR1 or Key-on wake-up 8. A-D conversion or Key-on wake-up
Interrupt Control
Each interrupt is controlled by an interrupt request bit, an interrupt enable bit, and the interrupt disable flag except for the software interrupt set by the BRK instruction. An interrupt occurs if the corresponding interrupt request and enable bits are "1" and the interrupt disable flag is "0". Interrupt enable bits can be set or cleared by software. Interrupt request bits can be cleared by software, but cannot be set by software. The BRK instruction cannot be disabled with any flag or bit. The I (interrupt disable) flag disables all interrupts except the BRK instruction interrupt. When several interrupts occur at the same time, the interrupts are received according to priority.
External Interrupt Pin Selection
The occurrence sources of the external interrupt INT2, INT3, and INT4 can be selected from either input from INT20, INT30, INT40 pin, or input from INT21, INT31, INT41 pin by the INT2, INT3, INT4 interrupt switch bit (bit 4 of address 002F16).
s Notes Interrupt Operation
By acceptance of an interrupt, the following operations are automatically performed: 1. The contents of the program counter and the processor status register are automatically pushed onto the stack. 2. The interrupt disable flag is set and the corresponding interrupt request bit is cleared. 3. The interrupt jump destination address is read from the vector table into the program counter. When setting of the following register or bit is changed, the interrupt request bit may be set to "1." * Interrupt edge selection register (address 003A16) * Interrupt source selection register (address 003916) * INT2, INT3, INT4 interrupt switch bit of Port control register 2 (bit 4 of address 002F16) Accept the interrupt after clearing the interrupt request bit to "0" after interrupt is disabled and the above register or bit is set.
19
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 6 Interrupt vector addresses and priority Interrupt Source Reset (Note 2) INT0 2 Input buffer full (IBF) INT1 Output buffer empty (OBE) Serial I/O1 reception Serial I/O1 transmission SCL, SDA Timer X Timer Y Timer 1 Timer 2 CNTR0 10 SCL, SDA CNTR1 11 Key-on wake-up Serial I/O2 I 2C INT2 I 2C INT3 INT4 A-D converter 16 Key-on wake-up BRK instruction 17 FFDD16 FFDC16 FFDF16 FFDE16 14 15 FFE316 FFE116 FFE216 FFE016 13 FFE516 FFE416 12 FFE716 FFE616 FFE916 FFE816 FFEB16 FFEA16 6 7 8 9 FFF316 FFF116 FFEF16 FFED16 FFF216 FFF016 FFEE16 FFEC16 3 FFF916 FFF816 FFFB16 FFFA16 Priority 1 Vector Addresses (Note 1) Low High FFFD16 FFFC16 Interrupt Request Generating Conditions At reset At detection of either rising or falling edge of INT0 input At input data bus buffer writing At detection of either rising or falling edge of INT1 input At output data bus buffer reading At completion of serial I/O1 data reception At completion of serial I/O1 transfer shift or when transmission buffer is empty At detection of either rising or falling edge of SCL or SDA At timer X underflow At timer Y underflow At timer 1 underflow At timer 2 underflow At detection of either rising or falling edge of CNTR0 input At detection of either rising or falling edge of SCL or SDA At detection of either rising or falling edge of CNTR1 input At falling of port P3 (at input) input logical level AND At completion of serial I/O2 data transfer At completion of data transfer At detection of either rising or falling edge of INT2 input At completion of data transfer At detection of either rising or falling edge of INT3 input At detection of either rising or falling edge of INT4 input At completion of A-D conversion At falling of port P3 (at input) input logical level AND At BRK instruction execution External interrupt (falling valid) Non-maskable software interrupt External interrupt (active edge selectable) External interrupt (active edge selectable) STP release timer underflow External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (falling valid) Valid when serial I/O2 is selected Valid when serial I/O1 is selected Valid when serial I/O1 is selected External interrupt (active edge selectable) External interrupt (active edge selectable) Remarks Non-maskable External interrupt (active edge selectable)
4
FFF716
FFF616
5
FFF516
FFF416
External interrupt (active edge selectable)
Notes 1: Vector addresses contain interrupt jump destination addresses. 2: Reset function in the same way as an interrupt with the highest priority.
20
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Interrupt request bit Interrupt enable bit
Interrupt disable flag (I)
BRK instruction Reset
Interrupt request
Fig. 15 Interrupt control
b7
b0 Interrupt edge selection register (INTEDGE : address 003A16) INT0 active edge selection bit INT1 active edge selection bit Not used (returns "0" when read) INT2 active edge selection bit INT3 active edge selection bit INT4 active edge selection bit Not used (returns "0" when read)
0 : Falling edge active 1 : Rising edge active b7 b0 Interrupt request register 2 (IREQ2 : address 003D16) CNTR0/SCL, SDA interrupt request bit CNTR1/key-on wake-up interrupt request bit Serial I/O2/I2C interrupt request bit INT2/I2C interrupt request bit INT3 interrupt request bit INT4 interrupt request bit AD converter/key-on wake-up interrupt request bit Not used (returns "0" when read) 0 : No interrupt request issued 1 : Interrupt request issued b7 b0 Interrupt control register 2 (ICON2 : address 003F16)
b7
b0 Interrupt request register 1 (IREQ1 : address 003C16) INT0/input buffer full interrupt request bit INT1/output buffer empty interrupt request bit Serial I/O1 receive interrupt request bit Serial I/O1 transmit/SCL, SDA interrupt request bit Timer X interrupt request bit Timer Y interrupt request bit Timer 1 interrupt request bit Timer 2 interrupt request bit
b7
b0
Interrupt control register 1 (ICON1 : address 003E16) INT0/input buffer full interrupt enable bit INT1/output buffer empty interrupt enable bit Serial I/O1 receive interrupt enable bit Serial I/O1 transmit/SCL, SDA interrupt enable bit Timer X interrupt enable bit Timer Y interrupt enable bit Timer 1 interrupt enable bit Timer 2 interrupt enable bit
CNTR0/SCL, SDA interrupt enable bit CNTR1/key-on wake-up interrupt enable bit Serial I/O2/I2C interrupt enable bit INT2/I2C interrupt enable bit INT3 interrupt enable bit INT4 interrupt enable bit AD converter/key-on wake-up interrupt enable bit Not used (returns "0" when read) (Do not write "1" to this bit) 0 : Interrupts disabled 1 : Interrupts enabled
Fig. 16 Structure of interrupt-related registers (1)
21
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
b0 Interrupt source selection register (INTSEL: address 003916) INT0/input buffer full interrupt source selection bit 0 : INT0 interrupt 1 : Input buffer full interrupt INT1/output buffer empty interrupt source selection bit 0 : INT1 interrupt 1 : Output buffer empty interrupt Serial I/O1 transmit/SCL,SDA interrupt source selection bit 0 : Serial I/O1 transmit interrupt 1 : SCL,SDA interrupt CNTR0/SCL,SDA interrupt source selection bit 0 : CNTR0 interrupt 1 : SCL,SDA interrupt Serial I/O2/I2C interrupt source selection bit 0 : Serial I/O2 interrupt 1 : I2C interrupt INT2/I2C interrupt source selection bit 0 : INT2 interrupt 1 : I2C interrupt CNTR1/key-on wake-up interrupt source selection bit 0 : CNTR1 interrupt 1 : Key-on wake-up interrupt (Do not write "1" to these bits simultaneously.) AD converter/key-on wake-up interrupt source selection bit 0 : A-D converter interrupt 1 : Key-on wake-up interrupt (Do not write "1" to these bits simultaneously.) (Do not write "1" to these bits simultaneously.)
Fig. 17 Structure of interrupt-related registers (2)
22
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Key Input Interrupt (Key-on Wake Up)
A Key input interrupt request is generated by applying "L" level to any pin of port P3 that have been set to input mode. In other words, it is generated when AND of input level goes from "1" to
"0". An example of using a key input interrupt is shown in Figure 18, where an interrupt request is generated by pressing one of the keys consisted as an active-low key matrix which inputs to ports P30-P33.
Port PXx "L" level output Port control register 1 Bit 5 = "1"
T TT
Port P37 direction register = "1" Port P37 latch
Key input interrupt request
P37 output
T
Port P36 direction register = "1"
TT
Port P36 latch
P36 output
T
Port P35 direction register = "1"
TT
Port P35 latch
P35 output
T
Port P34 direction register = "1"
TT
Port P34 latch
P34 output
T
P33 input
Port control register 1 Bit 4 = "1" TT Port P33 latch
Port P33 direction register = "0"
Port P3 Input reading circuit Comparator circuit
T
Port P32 direction register = "0"
TT
P32 input
Port P32 latch
T
Port P31 direction register = "0"
TT
P31 input
Port P31 latch
T
Port P30 direction register = "0"
TT
P30 input
Port P30 latch
T P-channel transistor for pull-up TT CMOS output buffer
Fig. 18 Connection example when using key input interrupt and port P3 block diagram
23
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
TIMERS
The 3886 group has four timers: timer X, timer Y, timer 1, and timer 2. The division ratio of each timer or prescaler is given by 1/(n + 1), where n is the value in the corresponding timer or prescaler latch. All timers are count down. When the timer reaches "0016", an underflow occurs at the next count pulse and the corresponding timer latch is reloaded into the timer and the count is continued. When a timer underflows, the interrupt request bit corresponding to that timer is set to "1".
Timer 1 and Timer 2
The count source of prescaler 12 is the oscillation frequency divided by 16. The output of prescaler 12 is counted by timer 1 and timer 2, and a timer underflow sets the interrupt request bit.
Timer X and Timer Y
Timer X and Timer Y can each select in one of four operating modes by setting the timer XY mode register.
(1) Timer Mode
The timer counts f(XIN)/16.
(2) Pulse Output Mode
b7 b0 Timer XY mode register (TM : address 002316) Timer X operating mode bit b1b0 0 0: Timer mode 0 1: Pulse output mode 1 0: Event counter mode 1 1: Pulse width measurement mode CNTR0 active edge selection bit 0: Interrupt at falling edge Count at rising edge in event counter mode 1: Interrupt at rising edge Count at falling edge in event counter mode Timer X count stop bit 0: Count start 1: Count stop Timer Y operating mode bit b5b4 0 0: Timer mode 0 1: Pulse output mode 1 0: Event counter mode 1 1: Pulse width measurement mode CNTR1 active edge selection bit 0: Interrupt at falling edge Count at rising edge in event counter mode 1: Interrupt at rising edge Count at falling edge in event counter mode Timer Y count stop bit 0: Count start 1: Count stop
Timer X (or timer Y) counts f(XIN)/16. Whenever the contents of the timer reach "0016", the signal output from the CNTR0 (or CNTR1) pin is inverted. If the CNTR0 (or CNTR1) active edge selection bit is "0", output begins at " H". If it is "1", output starts at "L". When using a timer in this mode, set the corresponding port P54 ( or port P55) direction register to output mode.
(3) Event Counter Mode
Operation in event counter mode is the same as in timer mode, except that the timer counts signals input through the CNTR0 or CNTR1 pin. When the CNTR0 (or CNTR1) active edge selection bit is "0", the rising edge of the CNTR0 (or CNTR1) pin is counted. When the CNTR0 (or CNTR1) active edge selection bit is "1", the falling edge of the CNTR0 (or CNTR1) pin is counted.
(4) Pulse Width Measurement Mode
If the CNTR0 (or CNTR1) active edge selection bit is "0", the timer counts f(XIN)/16 while the CNTR0 (or CNTR1) pin is at "H". If the CNTR0 (or CNTR1) active edge selection bit is "1", the timer counts while the CNTR0 (or CNTR1) pin is at "L". The count can be stopped by setting "1" to the timer X (or timer Y) count stop bit in any mode. The corresponding interrupt request bit is set each time a timer overflows. The count source for timer Y in the timer mode or the pulse output mode can be selected from either f(XIN)/16 or f(XCIN) by the timer Y count source selection bit of the port control register 2 (bit 5 of address 002F16).
Fig. 19 Structure of timer XY mode register
24
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Data bus
Oscillator f(XIN) (f(XCIN) in low-speed mode)
Divider 1/16 Pulse width measurement mode Prescaler X latch (8) Timer mode Pulse output mode Prescaler X (8) CNTR0 active edge selection bit "0" "1 " Event counter mode Timer X count stop bit To CNTR0 interrupt request bit Timer X (8) To timer X interrupt request bit Timer X latch (8)
P54/CNTR0
CNTR0 active edge selection "1" bit "0 "
Q Q
Toggle flip-flop T R Timer X latch write pulse Pulse output mode
Port P54 direction register
Port P54 latch Pulse output mode Data bus
Oscillator f(XIN) (f(XCIN) in low-speed mode) Oscillator f(XCIN)
Divider 1/16 Timer Y count source selection bit "0 " Prescaler Y latch (8) "1 " Pulse width measureTimer mode ment mode Pulse output mode Prescaler Y (8) Timer Y (8) To timer Y interrupt request bit Timer Y latch (8)
P55/CNTR1
CNTR1 active edge selection bit "0" "1 "
Event counter mode
Timer Y count stop bit To CNTR1 interrupt request bit
CNTR1 active edge selection "1" bit "0 "
Q Toggle flip-flop T Q R Timer Y latch write pulse Pulse output mode
Port P55 direction register
Port P55 latch
Pulse output mode Data bus
Prescaler 12 latch (8)
Timer 1 latch (8)
Timer 2 latch (8)
Oscillator f(XIN) (f(XCIN) in low-speed mode)
Divider 1/16 Prescaler 12 (8) Timer 1 (8) Timer 2 (8) To timer 2 interrupt request bit To timer 1 interrupt request bit
Fig. 20 Block diagram of timer X, timer Y, timer 1, and timer 2
25
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
SERIAL I/O Serial I/O1
Serial I/O1 can be used as either clock synchronous or asynchronous (UART) serial I/O. A dedicated timer is also provided for baud rate generation.
(1) Clock Synchronous Serial I/O Mode
Clock synchronous serial I/O1 mode can be selected by setting the serial I/O1 mode selection bit of the serial I/O1 control register (bit 6 of address 001A16) to "1". For clock synchronous serial I/O, the transmitter and the receiver must use the same clock. If an internal clock is used, transfer is started by a write signal to the TB/RB.
Data bus Serial I/O1 control register Address 001A16
Address 001816 Receive buffer register P44/RXD Receive shift register Shift clock P46/SCLK1/OBF10
Receive buffer full flag (RBF) Receive interrupt request (RI) Clock control circuit
BRG count source selection bit f(XIN) (f(XCIN) in low-speed mode) 1/4 P47/SRDY1/S1 F/F Falling-edge detector
Serial I/O1 synchronous clock selection bit Frequency division ratio 1/(n+1) Baud rate generator 1/4 Address 001C16 Clock control circuit Shift clock Transmit shift completion flag (TSC) Transmit interrupt source selection bit Transmit interrupt request (TI) Transmit buffer empty flag (TBE) Serial I/O1 status register Address 001916
P45/TXD
Transmit shift register Transmit buffer register Address 001816 Data bus
Fig. 21 Block diagram of clock synchronous serial I/O1
Transfer shift clock (1/2 to 1/2048 of the internal clock, or an external clock) Serial output TxD Serial input RxD D0 D0 D1 D1 D2 D2 D3 D3 D4 D4 D5 D5 D6 D6 D7 D7
Receive enable signal SRDY1 Write pulse to receive/transmit buffer register (address 001816) TBE = 0 RBF = 1 TSC = 1 Overrun error (OE) detection
TBE = 1 TSC = 0
Notes 1: As the transmit interrupt (TI), which can be selected, either when the transmit buffer has emptied (TBE=1) or after the transmit shift operation has ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the serial I/O1 control register. 2: If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial data is output continuously from the TxD pin. 3: The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes "1" .
Fig. 22 Operation of clock synchronous serial I/O1 function
26
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(2) Asynchronous Serial I/O (UART) Mode
Clock asynchronous serial I/O mode (UART) can be selected by clearing the serial I/O1 mode selection bit of the serial I/O1 control register to "0". Eight serial data transfer formats can be selected, and the transfer formats used by a transmitter and receiver must be identical. The transmit and receive shift registers each have a buffer, but the
two buffers have the same address in memory. Since the shift register cannot be written to or read from directly, transmit data is written to the transmit buffer register, and receive data is read from the receive buffer register. The transmit buffer register can also hold the next data to be transmitted, and the receive buffer register can hold a character while the next character is being received.
Data bus Address 001816
Receive buffer register OE Character length selection bit
Serial I/O1 control register Address 001A16 Receive buffer full flag (RBF) Receive interrupt request (RI) 1/16
P44/RXD
ST detector
7 bits 8 bits
Receive shift register PE FE SP detector Clock control circuit UART control register Address 001B16
Serial I/O1 synchronous clock selection bit P46/SCLK1/OBF10 BRG count source selection bit Frequency division ratio 1/(n+1) f(XIN) Baud rate generator (f(XCIN) in low-speed mode) Address 001C16 1/4 ST/SP/PA generator 1/16 P45/TXD Character length selection bit Transmit buffer register Address 001816 Data bus Transmit buffer empty flag (TBE) Serial I/O1 status register Address 001916 Transmit shift register Transmit shift completion flag (TSC) Transmit interrupt source selection bit Transmit interrupt request (TI)
Fig. 23 Block diagram of UART serial I/O1
27
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Transmit or receive clock Transmit buffer write signal TBE=0 TSC=0 TBE=1 TBE=0 TBE=1 TSC=1V
Serial output TXD
ST
D0
D1 1 start bit 7 or 8 data bit 1 or 0 parity bit 1 or 2 stop bit (s)
SP
ST
D0
D1
V
SP Generated at 2nd bit in 2-stop-bit mode
Receive buffer read signal RBF=0 RBF=1 RBF=1
Serial input RXD
ST
D0
D1
SP
ST
D0
D1
SP
Notes 1: Error flag detection occurs at the same time that the RBF flag becomes "1" (at 1st stop bit, during reception). 2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes "1," can be selected to occur depending on the setting of the transmit interrupt source selection bit (TIC) of the serial I/O1 control register. 3: The receive interrupt (RI) is set when the RBF flag becomes "1." 4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0.
Fig. 24 Operation of UART serial I/O1 function
[Serial I/O1 Control Register (SIO1CON)] 001A16
The serial I/O1 control register consists of eight control bits for the serial I/O function.
[Transmit Buffer Register/Receive Buffer Register (TB/RB)] 001816
The transmit buffer register and the receive buffer register are located at the same address. The transmit buffer is write-only and the receive buffer is read-only. If a character bit length is 7 bits, the MSB of data stored in the receive buffer is "0".
[UART Control Register (UARTCON)] 001B16
The UART control register consists of four control bits (bits 0 to 3) which are valid when asynchronous serial I/O is selected and set the data format of an data transfer and one bit (bit 4) which is always valid and sets the output structure of the P45/TXD pin.
[Baud Rate Generator (BRG)] 001C16
The baud rate generator determines the baud rate for serial transfer. The baud rate generator divides the frequency of the count source by 1/(n + 1), where n is the value written to the baud rate generator.
[Serial I/O1 Status Register (SIO1STS)] 001916
The read-only serial I/O1 status register consists of seven flags (bits 0 to 6) which indicate the operating status of the serial I/O function and various errors. Three of the flags (bits 4 to 6) are valid only in UART mode. The receive buffer full flag (bit 1) is cleared to "0" when the receive buffer register is read. If there is an error, it is detected at the same time that data is transferred from the receive shift register to the receive buffer register, and the receive buffer full flag is set. A write to the serial I/O1 status register clears all the error flags OE, PE, FE, and SE (bit 3 to bit 6, respectively). Writing "0" to the serial I/O1 enable bit SIOE (bit 7 of the serial I/O control register) also clears all the status flags, including the error flags. Bits 0 to 6 of the serial I/O1 status register are initialized to "0" at reset, but if the transmit enable bit (bit 4) of the serial I/O1 control register has been set to "1", the transmit shift completion flag (bit 2) and the transmit buffer empty flag (bit 0) become "1".
28
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
b0
Serial I/O1 status register (SIO1STS : address 001916) Transmit buffer empty flag (TBE) 0: Buffer full 1: Buffer empty Receive buffer full flag (RBF) 0: Buffer empty 1: Buffer full Transmit shift completion flag (TSC) 0: Transmit shift in progress 1: Transmit shift completed Overrun error flag (OE) 0: No error 1: Overrun error Parity error flag (PE) 0: No error 1: Parity error Framing error flag (FE) 0: No error 1: Framing error Summing error flag (SE) 0: (OE) U (PE) U (FE)=0 1: (OE) U (PE) U (FE)=1 Not used (returns "1" when read)
b7
b0
Serial I/O1 control register (SIO1CON : address 001A16) BRG count source selection bit (CSS) 0: f(XIN) (f(XCIN) in low-speed mode) 1: f(XIN)/4 (f(XCIN)/4 in low-speed mode) Serial I/O1 synchronous clock selection bit (SCS) 0: BRG output divided by 4 when clock synchronous serial I/O is selected, BRG output divided by 16 when UART is selected. 1: External clock input when clock synchronous serial I/O is selected, external clock input divided by 16 when UART is selected. SRDY1 output enable bit (SRDY) 0: P47 pin operates as ordinary I/O pin 1: P47 pin operates as SRDY1 output pin Transmit interrupt source selection bit (TIC) 0: Interrupt when transmit buffer has emptied 1: Interrupt when transmit shift operation is completed Transmit enable bit (TE) 0: Transmit disabled 1: Transmit enabled Receive enable bit (RE) 0: Receive disabled 1: Receive enabled Serial I/O1 mode selection bit (SIOM) 0: Clock asynchronous (UART) serial I/O 1: Clock synchronous serial I/O Serial I/O1 enable bit (SIOE) 0: Serial I/O disabled (pins P44 to P47 operate as ordinary I/O pins) 1: Serial I/O enabled (pins P44 to P47 operate as serial I/O pins)
b7
b0
UART control register (UARTCON : address 001B16) Character length selection bit (CHAS) 0: 8 bits 1: 7 bits Parity enable bit (PARE) 0: Parity checking disabled 1: Parity checking enabled Parity selection bit (PARS) 0: Even parity 1: Odd parity Stop bit length selection bit (STPS) 0: 1 stop bit 1: 2 stop bits P45/TXD P-channel output disable bit (POFF) 0: CMOS output (in output mode) 1: N-channel open drain output (in output mode) Not used (return "1" when read)
Fig. 25 Structure of serial I/O1 control registers
29
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Serial I/O2
The serial I/O2 function can be used only for clock synchronous serial I/O. For clock synchronous serial I/O the transmitter and the receiver must use the same clock. If the internal clock is used, transfer is started by a write signal to the serial I/O2 register.
b7
b0
Serial I/O2 control register (SIO2CON : address 001D16) Internal synchronous clock selection bits
b2 b1 b0
[Serial I/O2 Control Register (SIO2CON)] 001D16
The serial I/O2 control register contains seven bits which control various serial I/O functions.
0 0 0: f(XIN)/8 (f(XCIN)/8 in low-speed mode) 0 0 1: f(XIN)/16 (f(XCIN)/16 in low-speed mode) 0 1 0: f(XIN)/32 (f(XCIN)/32 in low-speed mode) 0 1 1: f(XIN)/64 (f(XCIN)/64 in low-speed mode) 1 1 0: f(XIN)/128 (f(XCIN)/128 in low-speed mode) 1 1 1: f(XIN)/256 (f(XCIN)/256 in low-speed mode) Serial I/O2 port selection bit 0: I/O port 1: SOUT2,SCLK2 signal output SRDY2 output enable bit 0: I/O port 1: SRDY2 signal output Transfer direction selection bit 0: LSB first 1: MSB first Serial I/O2 synchronous clock selection bit 0: External clock 1: Internal clock Comparator reference input selection bit 0: P00/P3REF input 1: Reference input fixed
Fig. 26 Structure of serial I/O2 control register
1/8
Internal synchronous clock selection bits
XCIN
Main clock divide ratio selection bits (Note) Divider "10" "00" "01"
1/16 1/32 1/64 1/128 1/256
Data bus
XIN
P73 latch
"0 " Serial I/O2 synchronous clock selection bit "1"
Synchronization circuit
P73/SRDY2
/INT21
SCLK2
SRDY2 "1 " SRDY2 output enable bit
"0 " External clock
P72 latch
"0 "
P72/SCLK2
"1 " Serial I/O2 port selection bit
Serial I/O counter 2 (3)
Serial I/O2 interrupt request
P71 latch
"0 "
P71/SOUT2
"1 " Serial I/O2 port selection bit
P70/SIN2
Serial I/O2 register (8)
Note: These are assigned to bits 7 and 6 of the CPU mode register (address 003B16). These bits select any of the high-speed mode, the middle-speed mode, and the low-speed mode.
Fig. 27 Block diagram of serial I/O2 function
30
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Transfer clock (Note 1) Serial I/O2 register write signal
(Note 2)
Serial I/O2 output SOUT2 Serial I/O2 input SIN2
D0
D1
D2
D3
D4
D5
D6
D7
Receive enable signal SRDY2
Serial I/O2 interrupt request bit set Notes 1: When the internal clock is selected as the transfer clock, the divide ratio can be selected by setting bits 0 to 2 of the serial I/O2 control register. 2: When the internal clock is selected as the transfer clock, the SOUT2 pin goes to high impedance after transfer completion.
Fig. 28 Timing of serial I/O2 function
31
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PULSE WIDTH MODULATION (PWM) OUTPUT CIRCUIT
The 3886 group has two PWM output circuits, PWM0 and PWM1, with 14-bit resolution respectively. These can operate independently. When the oscillation frequency XIN is 10 MHz, the minimum resolution bit width is 200 ns and the cycle period is 3276.8 s. The PWM timing generator supplies a PWM control signal based on a signal that is the frequency of the XIN clock.
The following explanation assumes f(XIN) = 8 MHz.
Data Bus
Set to "1" at write
PWM0L register (address 003116)
bit 7 bit 5 bit 0
bit 7
bit 0
PWM0H register (address 003016) PWM0 latch (14 bits)
MSB LSB
14
P30 latch P30/PWM00
14-bit PWM0 circuit
PWM0
PWM0 enable bit
f(XIN) (8MHz)
1/2 (4MHz)
PWM0 timing generator
(64 s period)
PWM0 output selection bit PWM0 enable bit
(4096 s period)
P30 direction register P56 latch P56/DA1/PWM01
PWM0 enable bit PWM0 output selection bit PWM0 enable bit P56 direction register
Fig. 29 PWM block diagram (PWM0)
32
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Data Setup (PWM0)
The PWM0 output pin also functions as port P30 or P56. The PWM0 output pin is selected from either P30/PWM00 or P56/PWM01 by bit 4 of the AD/DA control register (address 003416). The PWM0 output becomes enabled state by setting bit 6 of the port control register 1 (address 002E16). The high-order eight bits of output data are set in the PWM0H register (address 003016) and the low-order six bits are set in the PWM0L register (address 003116). PWM1 is set as the same way.
mum resolution (250 ns). "H" or "L" of the bit in the ADD part shown in Figure 30 is added to this "H" duration by the contents of the low-order 6-bit data according to the rule in Table 7. That is, only in the sub-period tm shown by Table 7 in the PWM cycle period T = 64t, its "H" duration is lengthened to the minimum resolution added to the length of other periods. For example, if the high-order eight bits of the 14-bit data are 0316 and the low-order six bits are 0516, the length of the "H"-level output in sub-periods t8, t24, t32, t40, and t56 is 4 , and its length is 3 in all other sub-periods. Time at the "H" level of each sub-period almost becomes equal, because the time becomes length set in the high-order 8 bits or becomes the value plus , and this sub-period t (= 64 s, approximate 15.6 kHz) becomes cycle period approximately.
PWM Operation
The 14-bit PWM data is divided into the low-order six bits and the high-order eight bits in the PWM latch. The high-order eight bits of data determine how long an "H"-level signal is output during each sub-period. There are 64 sub-periods in each period, and each sub-period is 256 ! (64 s) long. The signal is "H" for a length equal to N times , where is the miniTable 7 Relationship between low-order 6 bits of data and period set by the ADD bit Low-order 6 bits of data (PWML) 0 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0
LSB
Transfer From Register to Latch
Data written to the PWML register is transferred to the PWM latch at each PWM period (every 4096 s), and data written to the PWMH register is transferred to the PWM latch at each sub-period (every 64 s). The signal which is output to the PWM output pin is corresponding to the contents of this latch. When the PWML register is read, the latch contents are read. However, bit 7 of the PWML register indicates whether the transfer to the PWM latch is completed; the transfer is completed when bit 7 is "0" and it is not done when bit 7 is "1."
Sub-periods tm Lengthened (m=0 to 63) None m=32 m=16, 48 m=8, 24, 40, 56 m=4, 12, 20, 28, 36, 44, 52, 60 m=2, 6, 10, 14, 18, 22, 26, 30, 34, 38, 42, 46, 50, 54, 58, 62 m=1, 3, 5, 7, ................................................ ,57, 59, 61, 63
0 1 0 0 0 0 0
4096 s 64 s m=0 64 s m=7 64 s m=8 64 s m=9 64 s m=63
15.75 s
15.75 s
15.75 s
16.0 s
15.75 s
15.75 s
15.75 s
Pulse width modulation register H : 00111111 Pulse width modulation register L : 000101 Sub-periods where "H" pulse width is 16.0 s : Sub-periods where "H" pulse width is 15.75 s :
m = 8, 24, 32, 40, 56 m = all other values
Fig. 30 PWM timing
33
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Data 6A16 stored at address 003016 PWM0H register 5916 6A16 Bit 7 cleared after transfer 2416 Transfer from register to latch PWM0 latch (14bits) 165316 1A9316 1AA416 T = 4096 s (64 ! 64 s) 1AA416
Data 7B16 stored at address 003016 7B16 Data 3516 stored at address 003116 3516 B516 1EE416 Transfer from register to latch 1EF516
Data 2416 stored at address 003116 PWM0L register 1316 A416
When bit 7 of PWM0L is 0, transfer from register to latch is disabled.
t = 64 s
Example 1 PWM0 output 1 low-order 6-bit output: H L 6A16, 2416
6A
6B
6A
6B
6A
6B
6A
6B
6A
6B
6B
6B
6A
6B
6A
6B
6A
6B
6A
6B
6A
6B
6A
6B
6A
6B
6A
5
5
5
5
5
2
5
5
5
5
5
5
5
5
5
6B16 ************** 36 times (107)
6A16 ************* 28 times (106)
106 ! 64 + 36
Example 2 PWM0 output
6A
6A 6A
6A
6B
6A
6B
6A
6B
6A
6A
6A
6B
6A
6B
6A
6B
6A
6A
6A
6B
6A
6B
6A
6B
6A
6A
low-order 6-bit output: H L 6A16, 1816
4 6B16
**************
3 24 times
4 6A16 ******* 40 times
4
3
4 106 ! 64 + 24
4
3
4
t = 64 s (256 ! 0.25 s) Minimum resolution bit width = 0.25 s
PWM output 2 8-bit counter 02 01
6B ADD 00
6A
69
68
67
*******
02
01 ADD
6A
69
68
67
*******
02
01
FF
FE
FD
FC
*******
97
96
95
*******
02
01
00
FF
FE
FD
FC
*******
97
96
95
*******
The ADD portions with additional are determined by PWML.
H duration length specified by PWM0H
256 (64 s), fixed
Fig. 31 14-bit PWM timing (PWM0)
34
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
BUS INTERFACE
The 3886 group has a 2-byte bus interface function which is almost functionally equal to MELPS8-41 series and the control signal from the host CPU side can operate it (slave mode). It is possible to connect the 3886 group with the RD and WR separated CPU bus directly. Figure 34 shows the block diagram of the bus interface function. The data bus buffer function I/O pins (P42, P43, P46, P47, P50- P53, P8) also function as the normal digital port I/O pins. When bit 0 (data bus buffer enable bit) of the data bus buffer control register (address 002A16) is "0," these pins become the normal digital port I/O pins. When it is "1," these bits become the data bus buffer function I/O pins.
The selection of either the single data bus buffer mode, which uses 1 byte: data bus buffer 0 only, or the double data bus buffer mode, which uses 2 bytes: data bus buffer 0 and data bus buffer 1, is performed by bit 1 (data bus buffer function selection bit) of the data bus buffer control register (address 002A16). Port P47 becomes S1 input in the double data bus buffer mode. When data is written from the host CPU side, an input buffer full interrupt occurs. When data is read from the host CPU, an output buffer empty interrupt occurs. This microcomputer shares two input buffer full interrupt requests and two output buffer empty interrupt requests as shown in Figure 32, respectively.
Input buffer full flag 0 IBF0
Rising edge detection circuit Rising edge detection circuit
One-shot pulse generating circuit Input buffer full interrupt request signal IBF One-shot pulse generating circuit
Input buffer full flag 1 IBF1
Output buffer full flag 0 OBF0 Output buffer full flag 1 OBF1
OBE0
Rising edge detection circuit Rising edge detection circuit
One-shot pulse generating circuit Output buffer empty interrupt request signal OBE One-shot pulse generating circuit
OBE1
IBF0
IBF1
IBF OBF0
(OBE0)
Interrupt request is set at this rising edge
OBF1
(OBE1)
OBE
Interrupt request is set at this rising edge
Fig. 32 Interrupt request circuit of data bus buffer
35
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
b0 Data bus buffer control register (DBBCON : address 002A16)
Data bus buffer enable bit 0 : P50-P53, P8 I/O port 1 : Data bus buffer enabled Data bus buffer function selection bit 0 : Single data bus buffer mode (P47 functions as I/O port.) 1 : Double data bus buffer mode (P47 functions S1 input.) OBF0 output selection bit 0 : OBF00 valid 1 : OBF01 valid OBF00 output enable bit 0 : P42 functions as port I/O pin. 1 : P42 functions as OBF00 output pin. OBF01 output enable bit 0 : P43 functions as port I/O pin. 1 : P43 functions as OBF01 output pin. OBF10 output enable bit 0 : P46 functions as port I/O pin. 1 : P46 functions as OBF10 output pin. Input level selection bit 0 : CMOS level input 1 : TTL level input Reserved Do not write "1" to this bit.
b7
b0 Data bus buffer status register 0 (DBBSTS0 : address 002916)
Output buffer full flag 0 (OBF0) 0 : Buffer empty 1 : Buffer full Input buffer full flag 0 (IBF0) 0 : Buffer empty 1 : Buffer full User definable flag (U02) This flag can be defined by user freely. A00 flag (A00) This flag indicates the condition of A00 status when the IBF0 flag is set. User definable flag (U04-U07) This flag can be defined by user freely.
b7
b0 Data bus buffer status register 1 (DBBSTS1 : address 002C16)
Output buffer full flag 1 (OBF1) 0 : Buffer empty 1 : Buffer full Input buffer full flag 1 (IBF1) 0 : Buffer empty 1 : Buffer full User definable flag (U12) This flag can be defined by user freely. A01 flag (A01) This flag indicates the condition of A01 status when the IBF1 flag is set. User definable flag (U14-U17) This flag can be defined by user freely.
Fig. 33 Structure of bus interface related register
36
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(Address 002A16)
b7
b6
b5
b4
b3
b2
b1
b0
P42/INT0/OBF00 P43/INT1/OBF01
P50/A0 P51/INT20/S0 P52/INT30/R P53/INT40/W (Address 002916) U07 U06 U05 U04 A00 U02 IBF0 OBF0
P80/DQ0
Output data bus buffer 0 (Address 002816)
P81/DQ1
Internal data bus
P82/DQ2 Input data bus buffer 0
System bus
WR DBBSTS0
P83/DQ3
(Address 002816)
RD
DBB0
P84/DQ4
RD
DBB1
Input data bus buffer 1 P85/DQ5
WR
DBBSTS1
(Address 002B16)
P86/DQ6
P87/DQ7
Output data bus buffer 1 (Address 002B16) U17 U16 U15 U14 A01 U12 IBF1 OBF1
(Address 002C16)
P47/SRDY1/S1
P46/SCLK1/OBF10
Fig. 34 Bus interface device block diagram
37
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
[Data Bus Buffer Status Register 0, 1 (DBBSTS0, DBBSTS1)] 002916, 002C16
The data bus buffer status register 0, 1 consist of eight bits. Bits 0, 1, and 3 are read-only bits and indicate the condition of the data bus buffer. Bits 2, 4, 5, 6, and 7 are user definable flags which can be set by program, and can be read/written. This register can be read from the host CPU when the A0 pin is set to "H" only. *Bit 0: Output buffer full flag OBF0, OBF1 When writing data to the output data bus buffer, these flags are set to "1". When reading the output data bus buffer from the host CPU, these flags are cleared to "0". *Bit 1: Input buffer full flag IBF0, IBF1 When writing data from the host CPU to the input data bus buffer, these flags are set to "1". When reading the input data bus buffer from the slave CPU side, these flags are cleared to "0". *Bit 3: A0 flag A00, A01 When writing data from the host CPU to the input data bus buffer, the level of the A0 pin is latched.
[Input Data Bus Buffer Register 0, 1 (DBBIN0, DBBIN1)] 002816, 002B16
Data on the data bus is latched to DBBIN by writing request from the host CPU. Data of DBBIN can be read from the data bus buffer registers (address 002816 or 002B16) on SFR.
[Output Data Bus Buffer Register 0, 1 (DBBOUT0, DBBOUT1)] 002816, 002B16
When writing data to the data bus buffer registers (address 002816 or 002B16) on SFR, data is set to DBBOUT. Data of DBBOUT is output from the host CPU to the data bus by performing the reading request when the A0 pin is set to "L".
38
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 8 Function description of control I/O pins at bus interface function selected Pin P47/SRDY1 /S1 Name OBF00 output enable bit - OBF01 output enable bit - OBF10 output enable bit - Input /Output Input Functions Chip select input This is used for selecting the data bus buffer and is selected at "L" level. Address input This is used for selecting DBBSTS and DBBOUT when the host CPU is read. This is used for distinguishing command from data when writing to the host CPU. Chip select input This is used for selecting the data bus buffer and is selected at "L" level. This is a timing signal for reading data from the data bus buffer to the host CPU. This is a timing signal for writing data to the data bus buffer by the host CPU. Status output signal OBF00 signal is output. Status output signal OBF01 signal is output. Status output signal OBF10 signal is output.
S1
P50/A0
A0
-
-
-
Input
P51/INT20 /S0 P52/INT30 /R P53/INT40 /W P42/INT0 /OBF00 P43/INT1 /OBF01 P46/SCLK1 /OBF10
S0 R W OBF00 OBF01 OBF10
- - - 1 0 0
- - - 0 1 0
- - - 0 0 1
Input Input Output Output Output Output
39
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MULTI-MASTER I2C-BUS INTERFACE
The multi-master I2C-BUS interface is a serial communications circuit, conforming to the Philips I2C-BUS data transfer format. This interface, offering both arbitration lost detection and a synchronous functions, is useful for the multi-master serial communications. Figure 35 shows a block diagram of the multi-master I2C-BUS interface and Table 9 lists the multi-master I 2 C-BUS interface functions. This multi-master I2C-BUS interface consists of the I 2C address register, the I 2C data shift register, the I2C clock control register, the I2C control register, the I2C status register, the I2C start/stop condition control register and other control circuits. When using the multi-master I 2 C-BUS interface, set 1 MHz or more to .
Table 9 Multi-master I2C-BUS interface functions Item Function In conformity with Philips I2C-BUS standard: 10-bit addressing format 7-bit addressing format High-speed clock mode Standard clock mode In conformity with Philips I2C-BUS standard: Master transmission Master reception Slave transmission Slave reception 16.1 kHz to 400 kHz (at = 4 MHz) 20.2 kHz to 312.5 kHz (at = 5 MHz)
Format
Communication mode
SCL clock frequency
System clock = f(XIN)/2 (high-speed mode) = f(XIN)/8 (middle-speed mode)
b7 Interrupt generating circuit
Interrupt request signal (SCLSDAIRQ)
I2C address register
b0 Interrupt generating circuit
Interrupt request signal (I2CIRQ)
SA D6 SA D5 SA D4 SA D3 SA D2 SA D1 SA D0 RBW
S0D Address comparator
Serial data
(SDA)
Noise elimination circuit
Data control circuit
b7 I2C data shift register
S0
b0 b7
MST TRX BB PIN
b0
AL AAS AD0 LRB
S2D
STSP SIS SIP SSC4 SSC3 SSC2 SSC1 SSC0 SEL I2C start/stop condition control register
AL circuit
S1
Internal data bus
I2C status register
BB circuit
Serial clock
(SCL)
Noise elimination circuit
Clock control circuit
b7
ACK
b0
ACK F AST CCR4 CCR3 CCR2 CCR1 CCR0 BIT MODE
b7
TISS CLK STP
I2C clock control register S1D b0
10 BIT S AD AL S
ES0 BC2 BC1 BC0
S2 I2C clock control register
Clock division
S top sele ction
System clock ()
Bit counter
Fig. 35 Block diagram of multi-master I2C-BUS interface
V : Purchase of MITSUBISHI ELECTRIC CORPORATIONS I2C components conveys a license under the Philips I2C Patent Rights to use these components an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
40
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
[I2C Data Shift Register (S0)] 001216
The I2C data shift register (S0 : address 001216) is an 8-bit shift register to store receive data and write transmit data. When transmit data is written into this register, it is transferred to the outside from bit 7 in synchronization with the SCL clock, and each time one-bit data is output, the data of this register are shifted by one bit to the left. When data is received, it is input to this register from bit 0 in synchronization with the SCL clock, and each time one-bit data is input, the data of this register are shifted by one bit to the left. The minimum 2 cycles of are required from the rising of the SCL clock until input to this register. The I2C data shift register is in a write enable status only when the I2 C-BUS interface enable bit (ES0 bit : bit 3 of address 1516) of the I2C control register is "1." The bit counter is reset by a write instruction to the I2C data shift register. When both the ES0 bit and the MST bit of the I2C status register (address 001416) are "1," the SCL is output by a write instruction to the I 2C data shift register. Reading data from the I2C data shift register is always enabled regardless of the ES0 bit value. b7 b0 I2C address register (S0D: address 001316) Read/write bit Slave address
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RBW
Fig. 36 Structure of I2C address register
[I2C Address Register (S0D)] 001316
The I2C address register (address 001316) consists of a 7-bit slave address and a read/write bit. In the addressing mode, the slave address written in this register is compared with the address data to be received immediately after the START condition is detected. *Bit 0: Read/write bit (RBW) This is not used in the 7-bit addressing mode. In the 10-bit addressing mode, the first address data to be received is compared with the contents (SAD6 to SAD0 + RBW) of the I 2C address register. The RBW bit is cleared to "0" automatically when the stop condition is detected. *Bits 1 to 7: Slave address (SAD0-SAD6) These bits store slave addresses. Regardless of the 7-bit addressing mode and the 10-bit addressing mode, the address data transmitted from the master is compared with the contents of these bits.
41
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
[I2C Clock Control Register (S2)] 001616
The I2C clock control register (address 001616) is used to set ACK control, SCL mode and SCL frequency. *Bits 0 to 4: SCL frequency control bits (CCR0-CCR4) These bits control the SCL frequency. Refer to Table 10. *Bit 5: SCL mode specification bit (FAST MODE) This bit specifies the SCL mode. When this bit is set to "0," the standard clock mode is selected. When the bit is set to "1," the high-speed clock mode is selected. When connecting the bus of the high-speed mode I2C bus standard (maximum 400 kbits/s), use 8 MHz or more oscillation frequency f(XIN) and high-speed mode (2 division main clock). *Bit 6: ACK bit (ACK BIT) This bit sets the SDA status when an ACK clockV is generated. When this bit is set to "0," the ACK return mode is selected and SDA goes to "L" at the occurrence of an ACK clock. When the bit is set to "1," the ACK non-return mode is selected. The SDA is held in the "H" status at the occurrence of an ACK clock. However, when the slave address agree with the address data in the reception of address data at ACK BIT = "0," the SDA is automatically made "L" (ACK is returned). If there is a disagreement between the slave address and the address data, the SDA is automatically made "H" (ACK is not returned).
VACK clock: Clock for acknowledgment
b7
A CK
b0
A CK F AST B IT MODE CCR4 CCR3 CCR2 CCR1 CCR0
I2C clock control register (S2 : address 001616) SCL frequency control bits Refer to Table 10. SCL mode specification bit 0 : Standard clock mode 1 : High-speed clock mode ACK bit 0 : ACK is returned. 1 : ACK is not returned. ACK clock bit 0 : No ACK clock 1 : ACK clock
Fig. 37 Structure of I2C clock control register Table 10 Set values of I 2C clock control register and SCL frequency Setting value of CCR4-CCR0 CCR4 CCR3 CCR2 CCR1 CCR0 0 0 0 0 0 0 0 ... 0 0 0 0 0 0 0 ... 0 0 0 0 1 1 1 ... 0 0 1 1 0 0 1 ... 0 1 0 1 0 1 0 ... SCL frequency (at = 4 MHz, unit : kHz) (Note 1) Standard clock High-speed clock mode mode Setting disabled Setting disabled Setting disabled - (Note 2) - (Note 2) 100 83.3 500/CCR value (Note 3) 17.2 16.6 16.1 Setting disabled Setting disabled Setting disabled 333 250 400 (Note 3) 166 1000/CCR value (Note 3) 34.5 33.3 32.3
*Bit 7: ACK clock bit (ACK) This bit specifies the mode of acknowledgment which is an acknowledgment response of data transfer. When this bit is set to "0," the no ACK clock mode is selected. In this case, no ACK clock occurs after data transmission. When the bit is set to "1," the ACK clock mode is selected and the master generates an ACK clock each completion of each 1-byte data transfer. The device for transmitting address data and control data releases the SDA at the occurrence of an ACK clock (makes SDA "H") and receives the ACK bit generated by the data receiving device.
Note: Do not write data into the clock control register during transfer. If data is written during transfer, the I 2C clock generator is reset, so that data cannot be transferred normally. I2 C
1 1 1
1 1 1
1 1 1
0 1 1
1 0 1
Notes 1: Duty of SCL clock output is 50 %. The duty becomes 35 to 45 % only when the high-speed clock mode is selected and CCR value = 5 (400 kHz, at = 4 MHz). "H" duration of the clock fluctuates from -4 to +2 cycles of in the standard clock mode, and fluctuates from -2 to +2 cycles of in the high-speed clock mode. In the case of negative fluctuation, the frequency does not increase because "L" duration is extended instead of "H" duration reduction. These are value when SCL clock synchronization by the synchronous function is not performed. CCR value is the decimal notation value of the SCL frequency control bits CCR4 to CCR0. 2: Each value of SCL frequency exceeds the limit at = 4 MHz or more. When using these setting value, use of 4 MHz or less. 3: The data formula of SCL frequency is described below: /(8 ! CCR value) Standard clock mode /(4 ! CCR value) High-speed clock mode (CCR value 5) /(2 ! CCR value) High-speed clock mode (CCR value = 5) Do not set 0 to 2 as CCR value regardless of frequency. Set 100 kHz (max.) in the standard clock mode and 400 kHz (max.) in the high-speed clock mode to the SCL frequency by setting the SCL frequency control bits CCR4 to CCR0.
42
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
[I2C Control Register (S1D)] 001516
The I2C control register (address 001516) controls data communication format. *Bits 0 to 2: Bit counter (BC0-BC2) These bits decide the number of bits for the next 1-byte data to be transmitted. The I2C interrupt request signal occurs immediately after the number of count specified with these bits (ACK clock is added to the number of count when ACK clock is selected by ACK bit (bit 7 of address 001616)) have been transferred, and BC0 to BC2 are returned to "0002". Also when a START condition is received, these bits become "0002" and the address data is always transmitted and received in 8 bits. *Bit 3: I2C interface enable bit (ES0) This bit enables to use the multi-master I2C BUS interface. When this bit is set to "0," the use disable status is provided, so that the SDA and the SCL become high-impedance. When the bit is set to "1," use of the interface is enabled. When ES0 = "0," the following is performed. * PIN = "1," BB = "0" and AL = "0" are set (which are bits of the I2C status register at address 001416 ). * Writing data to the I2C data shift register (address 001216) is dis abled. *Bit 4: Data format selection bit (ALS) This bit decides whether or not to recognize slave addresses. When this bit is set to "0," the addressing format is selected, so that address data is recognized. When a match is found between a slave address and address data as a result of comparison or when a general call (refer to "(5) I 2C Status Register," bit 1) is received, transfer processing can be performed. When this bit is set to "1," the free data format is selected, so that slave addresses are not recognized. *Bit 5: Addressing format selection bit (10BIT SAD) This bit selects a slave address specification format. When this bit is set to "0," the 7-bit addressing format is selected. In this case, only the high-order 7 bits (slave address) of the I2C address register (address 001316) are compared with address data. When this bit is set to "1," the 10-bit addressing format is selected, and all the bits of the I 2C address register are compared with address data. *Bit 6: System clock stop selection bit (CLKSTP) When executing the WIT or STP instruction, this bit selects the condition of system clock provided to the multi-master I2C-BUS interface. When this bit is set to "0," system clock and operation of the multi-master I2C-BUS interface stop by executing the WIT or STP instruction. When this bit is set to "1," system clock and operation of the multimaster I 2 C-BUS interface do not stop even when the WIT instruction is executed. When the system clock stop selection bit is "1," do not execute the STP instruction. *Bit 7: I2C-BUS interface pin input level selection bit This bit selects the input level of the SCL and SDA pins of the multimaster I2C-BUS interface.
b7 b0 I2C control register (S1D : address 001516) Bit counter (Number of transmit/receive bits) b2 b1 b0 0 0 0:8 0 0 1:7 0 1 0:6 0 1 1:5 1 0 0:4 1 0 1:3 1 1 0:2 1 1 1:1 I2C-BUS interface enable bit 0 : Disabled 1 : Enabled Data format selection bit 0 : Addressing format 1 : Free data format Addressing format selection bit 0 : 7-bit addressing format 1 : 10-bit addressing format System clock stop selection bit 0 : System clock stop when executing WIT or STP instruction 1 : Not system clock stop when executing WIT instruction (Do not use the STP instruction.) I2C-BUS interface pin input level selection bit 0 : CMOS input 1 : SMBUS input
10 B IT TISS CLK SAD ALS ES0 BC2 BC1 BC0 STP
Fig. 38 Structure of I2C control register
43
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
[I2C Status Register (S1)] 001416
The I2C status register (address 001416) controls the I2C-BUS interface status. The low-order 4 bits are read-only bits and the high-order 4 bits can be read out and written to. Set "00002" to the low-order 4 bits, because these bits become the reserved bits at writing. *Bit 0: Last receive bit (LRB) This bit stores the last bit value of received data and can also be used for ACK receive confirmation. If ACK is returned when an ACK clock occurs, the LRB bit is set to "0." If ACK is not returned, this bit is set to "1." Except in the ACK mode, the last bit value of received data is input. The state of this bit is changed from "1" to "0" by executing a write instruction to the I2C data shift register (address 001216). *Bit 1: General call detecting flag (AD0) When the ALS bit is "0," this bit is set to "1" when a general call V whose address data is all "0" is received in the slave mode. By a general call of the master device, every slave device receives control data after the general call. The AD0 bit is set to "0" by detecting the STOP condition or START condition, or reset.
VGeneral call: The master transmits the general call address "0016" to all slaves.
*Bit 2: Slave address comparison flag (AAS) This flag indicates a comparison result of address data when the ALS bit is "0". In the slave receive mode, when the 7-bit addressing format is selected, this bit is set to "1" in one of the following conditions: * The address data immediately after occurrence of a START condition agrees with the slave address stored in the high-order 7 bits of the I2C address register (address 001316). * A general call is received. In the slave reception mode, when the 10-bit addressing format is selected, this bit is set to "1" with the following condition: * When the address data is compared with the I2C address register (8 bits consisting of slave address and RBW bit), the first bytes agree. This bit is set to "0" by executing a write instruction to the I2C data shift register (address 001216) when ES0 is set to "1" or reset. *Bit 3: Arbitration lostV detecting flag (AL) In the master transmission mode, when the SDA is made "L" by any other device, arbitration is judged to have been lost, so that this bit is set to "1." At the same time, the TRX bit is set to "0," so that immediately after transmission of the byte whose arbitration was lost is completed, the MST bit is set to "0." The arbitration lost can be detected only in the master transmission mode. When arbitration is lost during slave address transmission, the TRX bit is set to "0" and the reception mode is set. Consequently, it becomes possible to detect the agreement of its own slave address and address data transmitted by another master device.
VArbitration lost :The status in which communication as a master is disabled.
*Bit 4: I2C-BUS interface interrupt request bit (PIN) This bit generates an interrupt request signal. Each time 1-byte data is transmitted, the PIN bit changes from "1" to "0." At the same time, an interrupt request signal occurs to the CPU. The PIN bit is set to "0" in synchronization with a falling of the last clock (including the ACK clock) of an internal clock and an interrupt request signal occurs in synchronization with a falling of the PIN bit. When the PIN bit is "0," the SCL is kept in the "0" state and clock generation is disabled. Figure 40 shows an interrupt request signal generating timing chart. The PIN bit is set to "1" in one of the following conditions: * Executing a write instruction to the I2 C data shift register (address 001216). (This is the only condition which the prohibition of the internal clock is released and data can be communicated except for the start condition detection.) * When the ES0 bit is "0" * At reset * When writing "1" to the PIN bit by software The conditions in which the PIN bit is set to "0" are shown below: * Immediately after completion of 1-byte data transmission (including when arbitration lost is detected) * Immediately after completion of 1-byte data reception * In the slave reception mode, with ALS = "0" and immediately after completion of slave address agreement or general call address reception * In the slave reception mode, with ALS = "1" and immediately after completion of address data reception *Bit 5: Bus busy flag (BB) This bit indicates the status of use of the bus system. When this bit is set to "0," this bus system is not busy and a START condition can be generated. The BB flag is set/reset by the SCL, SDA pins input signal regardless of master/slave. This flag is set to "1" by detecting the start condition, and is set to "0" by detecting the stop condition. The condition of these detecting is set by the start/stop condition setting bits (SSC4-SSC0) of the I2C start/stop condition control register (address 001716). When the ES0 bit (bit 3) of the I2C control register (address 001516) is "0" or reset, the BB flag is set to "0." For the writing function to the BB flag, refer to the sections "START Condition Generating Method" and "STOP Condition Generating Method" described later.
44
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
*Bit 6: Communication mode specification bit (transfer direction specification bit: TRX) This bit decides a direction of transfer for data communication. When this bit is "0," the reception mode is selected and the data of a transmitting device is received. When the bit is "1," the transmission mode is selected and address data and control data are output onto the SDA in synchronization with the clock generated on the SCL. This bit is set/reset by software and hardware. About set/reset by hardware is described below. This bit is set to "1" by hardware when all the following conditions are satisfied: * When ALS is "0" * In the slave reception mode or the slave transmission mode * When the R/W bit reception is "1" This bit is set to "0" in one of the following conditions: * When arbitration lost is detected. * When a STOP condition is detected. * When writing "1" to this bit by software is invalid by the START condition duplication preventing function (Note). * With MST = "0" and when a START condition is detected. * With MST = "0" and when ACK non-return is detected. * At reset *Bit 7: Communication mode specification bit (master/slave specification bit: MST) This bit is used for master/slave specification for data communication. When this bit is "0," the slave is specified, so that a START condition and a STOP condition generated by the master are received, and data communication is performed in synchronization with the clock generated by the master. When this bit is "1," the master is specified and a START condition and a STOP condition are generated. Additionally, the clocks required for data communication are generated on the SCL. This bit is set to "0" in one of the following conditions. * Immediately after completion of 1-byte data transfer when arbitration lost is detected * When a STOP condition is detected. * Writing "1" to this bit by software is invalid by the START condition duplication preventing function (Note). * At reset
Note: START condition duplication preventing function The MST, TRX, and BB bits is set to "1" at the same time after confirming that the BB flag is "0" in the procedure of a START condition occurrence. However, when a START condition by another master device occurs and the BB flag is set to "1" immediately after the contents of the BB flag is confirmed, the START condition duplication preventing function makes the writing to the MST and TRX bits invalid. The duplication preventing function becomes valid from the rising of the BB flag to reception completion of slave address.
b7
b0 I2C status register (S1 : address 001416) Last receive bit (Note) 0 : Last bit = "0" 1 : Last bit = "1" General call detecting flag (Note) 0 : No general call detected 1 : General call detected Slave address comparison flag (Note) 0 : Address disagreement 1 : Address agreement Arbitration lost detecting flag (Note) 0 : Not detected 1 : Detected I2C-BUS interface interrupt request bit 0 : Interrupt request issued 1 : No interrupt request issued Bus busy flag 0 : Bus free 1 : Bus busy Communication mode specification bits 00 : Slave receive mode 01 : Slave transmit mode 10 : Master receive mode 11 : Master transmit mode
MST TRX BB PIN AL AAS AD0 LRB
Note: These bit and flags can be read out but cannot be written. Write "0" to these bits at writing.
Fig. 39 Structure of I2C status register
SCL PIN
I2CIRQ
Fig. 40 Interrupt request signal generating timing
45
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
START Condition Generating Method
When writing "1" to the MST, TRX, and BB bits of the I 2C status register (address 001416) at the same time after writing the slave address to the I 2C data shift register (address 001216) with the condition in which the ES0 bit of the I2C control register (address 001516) and the BB flag are "0", a START condition occurs. After that, the bit counter becomes "0002" and an SCL for 1 byte is output. The START condition generating timing is different in the standard clock mode and the high-speed clock mode. Refer to Figure 41, the START condition generating timing diagram, and Table 11, the START condition generating timing table.
START/STOP Condition Detecting Operation
The START/STOP condition detection operations are shown in Figures 43, 44, and Table 13. The START/STOP condition is set by the START/STOP condition set bit. The START/STOP condition can be detected only when the input signal of the SCL and SDA pins satisfy three conditions: SCL release time, setup time, and hold time (see Table 13). The BB flag is set to "1" by detecting the START condition and is reset to "0" by detecting the STOP condition. The BB flag set/reset timing is different in the standard clock mode and the high-speed clock mode. Refer to Table 13, the BB flag set/ reset time.
Note: When a STOP condition is detected in the slave mode (MST = 0), an interrupt request signal "I2CIRQ" occurs to the CPU.
I2C status register write signal SCL SDA Setup time Hold time SCL SDA BB flag High-speed clock mode 2.5 s (10 cycles) 6.5 s (26 cycles) 2.5 s (10 cycles) 6.5 s (26 cycles) SCL release time Setup time Hold time
BB flag reset time
Fig. 41 START condition generating timing diagram Table 11 START condition generating timing table Item Setup time Hold time START/STOP condition generating selection bit "0" "1" "0" "1" Standard clock mode 5.0 s (20 cycles) 13.0 s (52 cycles) 5.0 s (20 cycles) 13.0 s (52 cycles)
Fig. 43 START condition detecting timing diagram
SCL release time SCL SDA BB flag Setup time Hold time
BB flag reset time
Note: Absolute time at = 4 MHz. The value in parentheses denotes the number of cycles.
STOP Condition Generating Method
When the ES0 bit of the I2C control register (address 001516) is "1," write "1" to the MST and TRX bits, and write "0" to the BB bit of the I2C status register (address 001416) simultaneously. Then a STOP condition occurs. The STOP condition generating timing is different in the standard clock mode and the high-speed clock mode. Refer to Figure 42, the STOP condition generating timing diagram, and Table 12, the STOP condition generating timing table.
Fig. 44 STOP condition detecting timing diagram Table 13 START condition/STOP condition detecting conditions Standard clock mode SCL release time Setup time Hold time BB flag set/ reset time SSC value + 1 cycle (6.25 s) SSC value + 1 cycle < 4.0 s (3.25 s) 2 SSC value cycle < 4.0 s (3.0 s) 2 SSC value -1 + 2 cycles (3.375 s) 2 High-speed clock mode 4 cycles (1.0 s) 2 cycles (1.0 s) 2 cycles (0.5 s) 3.5 cycles (0.875 s)
I2C status register write signal SCL SDA Setup time Hold time
Note: Unit : Cycle number of system clock SSC value is the decimal notation value of the START/STOP condition set bits SSC4 to SSC0. Do not set "0" or an odd number to SSC value. The value in parentheses is an example when the I2C START/ STOP condition control register is set to "1816" at = 4 MHz.
Fig. 42 STOP condition generating timing diagram Table 12 STOP condition generating timing table Item Setup time Hold time START/STOP condition generating selection bit "0" "1" "0" "1" Standard clock mode 5.5 s (22 cycles) 13.5 s (54 cycles) 5.5 s (22 cycles) 13.5 s (54 cycles) High-speed clock mode 3.0 s (12 cycles) 7.0 s (28 cycles) 3.0 s (12 cycles) 7.0 s (28 cycles)
Note: Absolute time at = 4 MHz. The value in parentheses denotes the number of cycles.
46
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
[I2C START/STOP Condition Control Register (S2D)] 001716
The I2C START/STOP condition control register (address 001716) controls START/STOP condition detection. *Bits 0 to 4: START/STOP condition set bit (SSC4-SSC0) SCL release time, setup time, and hold time change the detection condition by value of the main clock divide ratio selection bit and the oscillation frequency f(XIN) because these time are measured by the internal system clock. Accordingly, set the proper value to the START/STOP condition set bits (SSC4 to SSC0) in considered of the system clock frequency. Refer to Table 13. Do not set "000002" or an odd number to the START/STOP condition set bit (SSC4 to SSC0). Refer to Table 14, the recommended set value to START/STOP condition set bits (SSC4-SSC0) for each oscillation frequency. *Bit 5: SCL/SDA interrupt pin polarity selection bit (SIP) An interrupt can occur when detecting the falling or rising edge of the SCL or SDA pin. This bit selects the polarity of the SCL or SDA pin interrupt pin. *Bit 6: SCL/SDA interrupt pin selection bit (SIS) This bit selects the pin of which interrupt becomes valid between the SCL pin and the SDA pin.
Note: When changing the setting of the SCL/SDA interrupt pin polarity selection bit, the SCL/SDA interrupt pin selection bit, or the I2 C-BUS interface enable bit ES0, the SCL/SDA interrupt request bit may be set. When selecting the SCL/SDA interrupt source, disable the interrupt before the SCL/SDA interrupt pin polarity selection bit, the SCL/ SDA interrupt pin selection bit, or the I 2C-BUS interface enable bit ES0 is set. Reset the request bit to "0" after setting these bits, and enable the interrupt.
10-bit addressing format To adapt the 10-bit addressing format, set the 10BIT SAD bit of the I2 C control register (address 001516) to "1." An address comparison is performed between the first-byte address data transmitted from the master and the 8-bit slave address stored in the I2C address register (address 001316). At the time of this comparison, an address comparison between the RBW bit of the I 2C address register (address 001316) and the R/W bit which is the last bit of the address data transmitted from the master is made. In the 10-bit addressing mode, the RBW bit which is the last bit of the address data not only specifies the direction of communication for control data, but also is processed as an address data bit. When the first-byte address data agree with the slave address, the AAS bit of the I2C status register (address 001416) is set to "1." After the second-byte address data is stored into the I2C data shift register (address 001216), perform an address comparison between the second-byte data and the slave address by software. When the address data of the 2 bytes agree with the slave address, set the RBW bit of the I2C address register (address 001316) to "1" by software. This processing can make the 7-bit slave address and R/W data agree, which are received after a RESTART condition is detected, with the value of the I2C address register (address 001316). For the data transmission format when the 10-bit addressing format is selected, refer to Figure 46, (3) and (4).
*Bit 7: START/STOP condition generating selection bit (STSPSEL) Setup/Hold time when the START/STOP condition is generated can be selected. Cycle number of system clock becomes standard for setup/hold time. Additionally, setup/hold time is different between the START condition and the STP condition. (Refer to Tables 11 and 12.) Set "1" to this bit when the system clock frequency is 4 MHz or more.
Address Data Communication
There are two address data communication formats, namely, 7-bit addressing format and 10-bit addressing format. The respective address communication formats are described below. 7-bit addressing format To adapt the 7-bit addressing format, set the 10BIT SAD bit of the I2C control register (address 001516) to "0." The first 7-bit address data transmitted from the master is compared with the high-order 7-bit slave address stored in the I2C address register (address 001316). At the time of this comparison, address comparison of the RBW bit of the I2 C address register (address 001316) is not performed. For the data transmission format when the 7-bit addressing format is selected, refer to Figure 46, (1) and (2).
47
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
STS P SE L
b0
SIS SIP SSC4 SSC3 SSC2 SSC1 SSC0
I2C START/STOP condition control register (S2D : address 001716) START/STOP condition set bit SCL/SDA interrupt pin polarity selection bit 0 : Falling edge active 1 : Rising edge active SCL/SDA interrupt pin selection bit 0 : SDA valid 1 : SCL valid START/STOP condition generating selection bit 0 : Setup/Hold time short mode 1 : Setup/Hold time long mode
Fig. 45 Structure of I2C START/STOP condition control register Table 14 Recommended set value to START/STOP condition set bits (SSC4-SSC0) for each oscillation frequency Oscillation frequency f(XIN) (MHz) 10 8 8 4 2 Main clock divide ratio 2 2 8 2 2 System clock (MHz) 5 4 1 2 1 START/STOP condition control register XXX11110 XXX11010 XXX11000 XXX00100 XXX01100 XXX01010 XXX00100 SCL release time (s) 6.2 s (31 cycles) 6.75 s (27 cycles) 6.25 s (25 cycles) 5.0 s (5 cycles) 6.5 s (13 cycles) 5.5 s (11 cycles) 5.0 s (5 cycles) Setup time (s) 3.2 s (16 cycles) 3.5 s (14 cycles) 3.25 s (13 cycles) 3.0 s (3 cycles) 3.5 s (7 cycles) 3.0 s (6 cycles) 3.0 s (3 cycles) Hold time (s) 3.0 s (15 cycles) 3.25 s (13 cycles) 3.0 s (12 cycles) 2.0 s (2 cycles) 3.0 s (6 cycles) 2.5 s (5 cycles) 2.0 s (2 cycles)
Note: Do not set "000002" or an odd number to the START/STOP condition set bit (SSC4 to SSC0).
S
Slave address R/W
A
Data
A
Data
A/A
P
7 bits "0" 1 to 8 bits 1 to 8 bits (1) A master-transmitter transnmits data to a slave-receiver
S
Slave address R/W
A
Data
A
Data
A
P
7 bits "1" 1 to 8 bits 1 to 8 bits (2) A master-receiver receives data from a slave-transmitter Slave address R/W 1st 7 bits Slave address 2nd bytes
S
A
A
Data
A
Data
A/A
P
7 bits "0" 8 bits 1 to 8 bits 1 to 8 bits (3) A master-transmitter transmits data to a slave-receiver with a 10-bit address Slave address R/W 1st 7 bits Slave address 2nd bytes Slave address R/W 1st 7 bits
S
A
A
Sr
A
Data 1 to 8 bits
A
Data 1 to 8 bits
A
P
"1" 7 bits "0" 8 bits 7 bits (4) A master-receiver receives data from a slave-transmitter with a 10-bit address
S : START condition A : ACK bit Sr : Restart condition
P : STOP condition R/W : Read/Write bit
Fig. 46 Address data communication format
48
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Example of Master Transmission
An example of master transmission in the standard clock mode, at the SCL frequency of 100 kHz and in the ACK return mode is shown below. Set a slave address in the high-order 7 bits of the I2C address register (address 001316) and "0" into the RBW bit. Set the ACK return mode and SCL = 100 kHz by setting "8516" in the I2C clock control register (address 001616). Set "0016" in the I2C status register (address 001416) so that transmission/reception mode can become initializing condition. Set a communication enable status by setting "0816" in the I2C control register (address 001516). Confirm the bus free condition by the BB flag of the I 2C status register (address 001416). Set the address data of the destination of transmission in the high-order 7 bits of the I2C data shift register (address 001216) and set "0" in the least significant bit. Set "F016" in the I2C status register (address 001416) to generate a START condition. At this time, an SCL for 1 byte and an ACK clock automatically occur. Set transmit data in the I2C data shift register (address 001216). At this time, an SCL and an ACK clock automatically occur. When transmitting control data of more than 1 byte, repeat step . Set "D016" in the I2C status register (address 001416) to generate a STOP condition if ACK is not returned from slave reception side or transmission ends.
sPrecautions when using multi-master I2CBUS interface
(1) Read-modify-write instruction The precautions when the read-modify-write instruction such as SEB, CLB etc. is executed for each register of the multi-master I2C-BUS interface are described below. * I2C data shift register (S0: address 001216) When executing the read-modify-write instruction for this register during transfer, data may become a value not intended. * I2C address register (S0D: address 001316) When the read-modify-write instruction is executed for this register at detecting the STOP condition, data may become a value not intended. It is because H/W changes the read/write bit (RBW) at the above timing. * I2C status register (S1: address 001416) Do not execute the read-modify-write instruction for this register because all bits of this register are changed by H/W. * I2C control register (S1D: address 001516) When the read-modify-write instruction is executed for this register at detecting the START condition or at completing the byte transfer, data may become a value not intended. Because H/W changes the bit counter (BC0-BC2) at the above timing. * I2C clock control register (S2: address 001616) The read-modify-write instruction can be executed for this register. * I 2 C START/STOP condition control register (S2D: address 001716) The read-modify-write instruction can be executed for this register.
Example of Slave Reception
An example of slave reception in the high-speed clock mode, at the SCL frequency of 400 kHz, in the ACK non-return mode and using the addressing format is shown below. Set a slave address in the high-order 7 bits of the I2C address register (address 001316) and "0" in the RBW bit. Set the no ACK clock mode and SCL = 400 kHz by setting "2516" in the I2C clock control register (address 001616). Set "0016" in the I2C status register (address 001416) so that transmission/reception mode can become initializing condition. Set a communication enable status by setting "0816" in the I2C control register (address 001516). When a START condition is received, an address comparison is performed. *When all transmitted addresses are "0" (general call): AD0 of the I 2C status register (address 001416) is set to "1" and an interrupt request signal occurs. * When the transmitted addresses agree with the address set in : ASS of the I2C status register (address 001416) is set to "1" and an interrupt request signal occurs. * In the cases other than the above AD0 and AAS of the I2C status register (address 001416) are set to "0" and no interrupt request signal occurs. Set dummy data in the I2C data shift register (address 001216). When receiving control data of more than 1 byte, repeat step . When a STOP condition is detected, the communication ends.
49
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(2) START condition generating procedure using multi-master 1. Procedure example (The necessary conditions of the generating procedure are described as the following 2 to 5. LDA -- SEI BBS 5, S1, BUSBUSY cess) BUSFREE: STA S0 LDM #$F0, S1 CLI BUSBUSY: CLI
..... ..... .....
(Taking out of slave address value) (Interrupt disabled) (BB flag confirming and branch pro-
(4) Writing to I2C status register Do not execute an instruction to set the PIN bit to "1" from "0" and an instruction to set the MST and TRX bits to "0" from "1" simultaneously. It is because it may enter the state that the SCL pin is released and the SDA pin is released after about one machine cycle. Do not execute an instruction to set the MST and TRX bits to "0" from "1" simultaneously when the PIN bit is "1." It is because it may become the same as above. (5) Process of after STOP condition generating Do not write data in the I2C data shift register S0 and the I2C status register S1 until the bus busy flag BB becomes "0" after generating the STOP condition in the master mode. It is because the STOP condition waveform might not be normally generated. Reading to the above registers do not have the problem. (6) STOP condition input at 7th clock pulse In the slave mode, the STOP condition is input at the 7th clock pulse while receiving a slave address or data. As the clock pulse is continuously input, the SDA line may be held at LOW even if flag BB is set to "0" (only for M38867M8A and M38867E8). Countermeasure: Write dummy data to the I2C shift register or reset the ES0 bit in the S1D register (ES0 = "L" ES0 = "H") during a stop condition interrupt routine with flag PIN = "1". Note: Do not use the read-modify-write instruction at this time. Furthermore, when the ES0 bit is set to "0", it becomes a general-purpose port; so that the port must be set to input mode or "H". (7) ES0 bit switch In standard clock mode when SSC = "000102" or in high-speed clock mode, flag BB may switch to "1" if ES0 bit is set to "1" when SDA is "L". Countermeasure: Set ES0 to "1" when SDA is "H".
(Writing of slave address value) (Trigger of START condition generating) (Interrupt enabled)
(Interrupt enabled)
2. Use "Branch on Bit Set" of "BBS 5, $0014, -" for the BB flag confirming and branch process. 3. Use "STA $12, STX $12" or "STY $12" of the zero page addressing instruction for writing the slave address value to the I2C data shift register. 4. Execute the branch instruction of above 2 and the store instruction of above 3 continuously shown the above procedure example. 5. Disable interrupts during the following three process steps: * BB flag confirming * Writing of slave address value * Trigger of START condition generating When the condition of the BB flag is bus busy, enable interrupts immediately. (3) RESTART condition generating procedure This cannot be applied when the external memory is used and the bus cycle is extended by ONW function. 1. Procedure example (The necessary conditions of the generating procedure are described as the following 2 to 4.) Execute the following procedure when the PIN bit is "0." LDM #$00, S1 LDA -- SEI STA S0 LDM #$F0, S1 CLI
..... .....
(Select slave receive mode) (Taking out of slave address value) (Interrupt disabled) (Writing of slave address value) (Trigger of RESTART condition generating) (Interrupt enabled)
2. Select the slave receive mode when the PIN bit is "0." Do not write "1" to the PIN bit. Neither "0" nor "1" is specified for the writing to the BB bit. The TRX bit becomes "0" and the SDA pin is released. 3. The SCL pin is released by writing the slave address value to the I2C data shift register. 4. Disable interrupts during the following two process steps: * Writing of slave address value * Trigger of RESTART condition generating
50
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
A-D CONVERTER [A-D Conversion Register 1,2 (AD1, AD2)] 003516, 003816
The A-D conversion register is a read-only register that stores the result of an A-D conversion. When reading this register during an A-D conversion, the previous conversion result is read. Bit 7 of the A-D conversion register 2 is the conversion mode selection bit. When this bit is set to "0," the A-D converter becomes the 10-bit A-D mode. When this bit is set to "1," that becomes the 8-bit A-D mode. The conversion result of the 8-bit A-D mode is stored in the A-D conversion register 1. As for 10-bit A-D mode, 10-bit reading or 8-bit reading can be performed by selecting the reading procedure of the A-D conversion register 1, 2 after A-D conversion is completed (in Figure 48). The A-D conversion register 1 performs the 8-bit reading inclined to MSB after reset, the A-D conversion is started, or reading of the A-D converter register 1 is generated; and the register becomes the 8-bit reading inclined to LSB after the A-D converter register 2 is generated.
Channel Selector
The channel selector selects one of ports P60/AN0 to P67/AN7, and inputs the voltage to the comparator.
Comparator and Control Circuit
The comparator and control circuit compares an analog input voltage with the comparison voltage, and then stores the result in the A-D conversion registers 1, 2. When an A-D conversion is completed, the control circuit sets the A-D conversion completion bit and the A-D interrupt request bit to "1". Note that because the comparator consists of a capacitor coupling, set f(XIN) to 500 kHz or more during an A-D conversion.
b7
b0
AD/DA control register (ADCON : address 003416) Analog input pin selection bits
b2 b1 b0
[AD/DA Control Register (ADCON)] 003416
The AD/DA control register controls the A-D conversion process. Bits 0 to 2 select a specific analog input pin. Bit 3 signals the completion of an A-D conversion. The value of this bit remains at "0" during an A-D conversion, and changes to "1" when an A-D conversion ends. Writing "0" to this bit starts the A-D conversion.
0 0 0 0 1 1 1 1
0 0 1 1 0 0 1 1
0: P60/AN0 1: P61/AN1 0: P62/AN2 1: P63/AN3 0: P64/AN4 1: P65/AN5 0: P66/AN6 1: P67/AN7
A-D conversion completion bit 0: Conversion in progress 1: Conversion completed PWM0 output pin selection bit 0: P56/PWM01 1: P30/PWM00 PWM1 output pin selection bit 0: P57/PWM11 1: P31/PWM10 DA1 output enable bit 0: DA1 output disabled 1: DA1 output enabled DA2 output enable bit 0: DA2 output disabled 1: DA2 output enabled
Comparison Voltage Generator
The comparison voltage generator divides the voltage between AVSS and VREF into 1024, and outputs the divided voltages in the 10-bit A-D mode (256 division in 8-bit A-D mode). The A-D converter successively compares the comparison voltage Vref in each mode, dividing the VREF (see below), with the input voltage. * 10-bit A-D mode (10-bit reading) VREF Vref = 1024 ! n (n = 0-1023) * 10-bit A-D mode (8-bit reading) VREF Vref = 256 ! n (n = 0-255) * 8-bit A-D mode VREF Vref = 256 ! (n-0.5) (n = 1-255) =0 (n = 0)
Fig. 47 Structure of AD/DA control register
10-bit reading (Read address 003816 before 003516)
b7
(Address 003816) (Address 003516)
0 b7
b0 b9 b8
b0 b7 b6 b5 b4 b3 b2 b1 b0
Note: Bits 2 to 6 of address 003816 becomes "0"at reading.
8-bit reading (Read only address 003516)
b7
(Address 003516)
b0 b9 b8 b7 b6 b5 b4 b3 b2
Fig. 48 Structure of 10-bit A-D mode reading
51
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Data bus
AD/DA control register (Address 003416)
b7
b0
3 P60/AN0 P61/AN1 P62/AN2 P63/AN3 P64/AN4 P65/AN5 P66/AN6 P67/AN7 A-D control circuit A-D interrupt request
Channel selector
Comparator
A-D conversion register 2 (Address 003816) A-D conversion register 1 (Address 003516) 10 Resistor ladder
VREF AVSS
Fig. 49 Block diagram of A-D converter
52
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
D-A CONVERTER
The 3886 group has two internal D-A converters (DA1 and DA2) with 8-bit resolution. The D-A converter is performed by setting the value in each D-A conversion register. The result of D-A conversion is output from the DA1 or DA2 pin by setting the DA output enable bit to "1". When using the D-A converter, the corresponding port direction register bit (P56/DA1/PWM01 or P57/DA2/PWM11) must be set to "0" (input status). The output analog voltage V is determined by the value n (decimal notation) in the D-A conversion register as follows: V = VREF ! n/256 (n = 0 to 255) Where VREF is the reference voltage. At reset, the D-A conversion registers are cleared to "0016", the DA output enable bits are cleared to "0", and the P56/DA1/PWM01 and P57/DA2/PWM11 pins become high impedance. The DA output does not have buffers. Accordingly, connect an external buffer when driving a low-impedance load. Set VCC to 4.0 V or more when using the D-A converter.
D-A1 conversion register (8) DA1 output enable bit P56/DA1/PWM01
Data bus
R-2R resistor ladder
D-A2 conversion register (8) DA2 output enable bit P57/DA2/PWM11
R-2R resistor ladder
Fig. 50 Block diagram of D-A converter
"0" DA1 output enable bit R P56/DA1/PWM01 "1" MSB D-A1 conversion register "0" "1" 2R
R
R
R
R
R
R
2R
2R
2R
2R
2R
2R
2R
2R LSB
AVSS VREF
Fig. 51 Equivalent connection circuit of D-A converter (DA1)
53
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
COMPARATOR CIRCUIT Comparator Configuration
The comparator circuit consists of resistors, comparators, a comparator control circuit, the comparator reference input selection bit (bit 7 of address 001D16), a comparator data register (address 002D16), the comparator reference power source input pin (P00/ P3REF) and analog signal input pins (P30-P37). The analog input pin (P30-P37) also functions as an ordinary digital port.
Comparator Operation
To activate the comparator, first set port P3 to input mode by setting the corresponding direction register (address 000716) to "0" to use port P3 as an analog voltage input pin. The internal fixed analog voltage (VCC ! 29/32) can be generated by setting "1" to the comparator reference input selection bit (bit 7) of the serial I/O2 control register (address 001D16). (The internal fixed analog voltage becomes about 4.5 V at VCC = 5.0 V.) When setting "0" to the comparator reference input selection bit, the P00/P3REF pin becomes the comparator reference power source input pin and it is possible to input the comparator reference power source optionally from the external. The voltage comparison is immediately
performed by the writing operation to the comparator data register (address 002D16). After 14 cycles of the internal system clock (the time required for the comparison), the comparison result is stored in the comparator register (address 002D16). If the analog input voltage is greater than the internal reference voltage, each bit of this register is "1"; if it is less than the internal reference voltage, each bit of this register is "0". To perform another comparison, the voltage comparison must be performed again by writing to the comparator data register (address 002D16). Read the result when 14 cycles of or more have passed after the comparator operation starts. The ladder resistor is turned on during 14 cycles of , which is required for the comparison, and the reference voltage is generated. An unnecessary current is not consumed because the ladder resistor is turned off while the comparator operation is not performed. Since the comparator consists of capacitor coupling, the electric charge is lost if the clock frequency is low. Keep that the clock frequency is 1 MHz or more during the comparator operation. Do not execute the STP, WIT, or port P3 I/O instruction.
Data bus 8 P3 (8) P37
Comparator
8 Comparator data register (address 002D16)
b0
P36
Comparator
Comparator reference input selection bit (bit 7) of serial I/O2 control register(address 001D16)
"0"
P30
Comparator
VCC
VCC!29/32
"1"
P00/P3REF
Comparator Comparator connecting control circuit Ladder resistor signal connecting signal VSS
Fig. 52 Comparator circuit
54
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
WATCHDOG TIMER
The watchdog timer gives a mean of returning to the reset status when a program cannot run on a normal loop (for example, because of a software run-away). The watchdog timer consists of an 8-bit watchdog timer L and an 8-bit watchdog timer H.
Standard Operation of Watchdog Timer
When any data is not written into the watchdog timer control register (address 001E16) after resetting, the watchdog timer is in the stop state. The watchdog timer starts to count down by writing an optional value into the watchdog timer control register (address 001E16) and an internal reset occurs at an underflow of the watchdog timer H. Accordingly, programming is usually performed so that writing to the watchdog timer control register (address 001E16) may be started before an underflow. When the watchdog timer control register (address 001E16) is read, the values of the high-order 6 bits of the watchdog timer H, STP instruction disable bit, and watchdog timer H count source selection bit are read.
qWatchdog timer H count source selection bit operation Bit 7 of the watchdog timer control register (address 001E16) permits selecting a watchdog timer H count source. When this bit is set to "0", the count source becomes the underflow signal of watchdog timer L. The detection time is set to f(XIN)=131.072 ms at 8 MHz frequency and f(XCIN)=32.768 s at 32 kHz frequency. When this bit is set to "1", the count source becomes the signal divided by 16 for f(XIN) (or f(XCIN)). The detection time in this case is set to f(XIN)= 512 s at 8 MHz frequency and f(XCIN)=128 ms at 32 kHz frequency. This bit is cleared to "0" after resetting. qOperation of STP instruction disable bit Bit 6 of the watchdog timer control register (address 001E16) permits disabling the STP instruction when the watchdog timer is in operation. When this bit is "0", the STP instruction is enabled. When this bit is "1", the STP instruction is disabled. Once the STP instruction is executed, an internal reset occurs. When this bit is set to "1", it cannot be rewritten to "0" by program. This bit is cleared to "0" after resetting.
Initial Value of Watchdog Timer
At reset or writing to the watchdog timer control register (address 001E16), each watchdog timer H and L is set to "FF16."
XCIN "10" Main clock division ratio selection bits (Note) XIN
"FF16" is set when watchdog timer control register is written to. Watchdog timer L (8) 1/16
Data bus "FF16" is set when watchdog timer control register is written to.
"0" "1" Watchdog timer H (8)
"00" "01"
Watchdog timer H count source selection bit
STP instruction disable bit STP instruction Reset circuit Internal reset
RESET
Note: Either high-speed, middle-speed or low-speed mode is selected by bits 7 and 6 of the CPU mode register.
Fig. 53 Block diagram of Watchdog timer
b7
b0
Watchdog timer control register (WDTCON : address 001E16)
Watchdog timer H (for read-out of high-order 6 bit) STP instruction disable bit 0: STP instruction enabled 1: STP instruction disabled Watchdog timer H count source selection bit 0: Watchdog timer L underflow 1: f(XIN)/16 or f(XCIN)/16
Fig. 54 Structure of Watchdog timer control register
55
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
RESET CIRCUIT
To reset the microcomputer, RESET pin should be held at an "L" level for 2 s or more. Then the RESET pin is returned to an "H" level (the power source voltage should be between 2.7 V and 5.5 V (4.0 V to 5.5 V for flash memory version), and the oscillation should be stable), reset is released. After the reset is completed, the program starts from the address contained in address FFFD16 (high-order byte) and address FFFC16 (low-order byte). Make sure that the reset input voltage is less than 0.54 V for VCC of 2.7 V. For flash memory version, make sure that the reset input voltage is less than 0.8 V for Vcc of 4.0 V.
Poweron Power source voltage 0V Reset input voltage 0V (Note)
RESET
VCC
0.2VCC
Note : Reset release voltage ; Vcc=2.7 V (Vcc = 4.0 V for flash memory version)
RESET
VCC Power source voltage detection circuit
Fig. 55 Reset circuit example
XIN
RESET Internal reset
Address
?
?
?
?
FFFC
F FFD
ADH,L
Reset address from the vector table.
Data
?
?
?
?
ADL
ADH
SYNC
XIN: 10.5 to 18.5 clock cycles Notes 1: The frequency relation of f(XIN) and f() is f(XIN)=8 * f(). 2: The question marks (?) indicate an undefined state that depends on the previous state.
Fig. 56 Reset sequence
56
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Address Register contents (1) (2) (3) (4) (5) (6) (7) (8) (9) Port P0 (P0) Port P0 direction register (P0D) Port P1 (P1) Port P1 direction register (P1D) Port P2 (P2) Port P2 direction register (P2D) Port P3 (P3) Port P3 direction register (P3D) Port P4 (P4) 000016 000116 000216 000316 000416 000516 000616 000716 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16 001016 001116 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 (33) Prescaler 12 (PRE12) (34) Timer 1 (T1) (35) Timer 2 (T2) (36) Timer XY mode register (TM) (37) Prescaler X (PREX) (38) Timer X (TX) (39) Prescaler Y (PREY) (40) Timer Y (TY)
Address Register contents 002016 002116 002216 002316 002416 002516 002616 002716 FF16 0116 FF16 0016 FF16 FF16 FF16 FF16
(41) Data bus buffer register 0 (DBB0) 002816 X X X X X X X X (42) Data bus buffer status register 0 (DBBSTS0) (43) Data bus buffer control register (DBBCON) 002916 002A16 0016 0016
(10) Port P4 direction register (P4D) (11) Port P5 (P5) (12) Port P5 direction register (P5D) (13) Port P6 (P6) (14) Port P6 direction register (P6D) (15) Port P7 (P7) (16) Port P7 direction register (P7D) (17) Port P8 (P8) (18) Port P8 direction register (P8D) (19) I2C data shift register (S0) (20) I2C address register (S0D) (21) I2C status register (S1) (22) I2C control register (S1D) (23) I2C clock control register (S2) (24) I2C start/stop condition control register (S2D) (25) Transmit/Receive buffer register (TB/RB) (26) Serial I/O1 status register (SIO1STS) (27) Serial I/O1 control register (SIO1CON) (28) UART control register (UARTCON) (29) Baud rate generator (BRG) (30) Serial I/O2 control register (SIO2CON) (31) Watchdog timer control register (WDTCON) (32) Serial I/O2 register (SIO2)
(44) Data bus buffer register 1 (DBB1) 002B16 X X X X X X X X (45) Data bus buffer status register 1 (DBBSTS1) (46) Comparator data register (CMPD) (47) Port control register 1 (PCTL1) (48) Port control register 2 (PCTL2) (49) PWM0H register (PWM0H) (50) PWM0L register (PWM0L) (51) PWM1H register (PWM1H) (52) PWM1L register (PWM1L) (53) AD/DA control register (ADCON) (54) A-D conversion register 1 (AD1) (55) D-A1 conversion register (DA1) (56) D - 2 conversion register (DA2) A (57) A - conversion register 2 (AD2) D (58) Interrupt source selection register (INTSEL) (59) Interrupt edge selection register (INTEDGE) (60) CPU mode register (CPUM) (61) Interrupt request register 1 (IREQ1) (62) Interrupt request register 2 (IREQ2) (63) Interrupt control register 1 (ICON1) (64) Interrupt control register 2 (ICON2) 002C16 0016
002D16 X X X X X X X X 002E16 002F16 0016 0016
003016 X X X X X X X X 003116 X 0 X X X X X X 003216 X X X X X X X X 003316 X 0 X X X X X X 003416 0 0 0 0 1 0 0 0 003516 X X X X X X X X 003616 003716 0016 0016
001216 X X X X X X X X 001316 0016
001416 0 0 0 1 0 0 0 X 001516 001616 0016 0016
001716 0 0 0 1 1 0 1 0 001816 X X X X X X X X 001916 1 0 0 0 0 0 0 0 001A16 0016
003816 0 0 0 0 0 0 X X 003916 003A16 0016 0016
T
001B16 1 1 1 0 0 0 0 0 001C16 X X X X X X X X 001D16 0016
003B16 0 1 0 0 1 0 003C16 003D16 003E16 003F16 0016 0016 0016 0016 0016 0016
0
001E16 0 0 1 1 1 1 1 1 001F16 X X X X X X X X
(65) Flash memory control register (FCON) 0FFE16 (66) Flash command register (FCMD) Note : T The initial values depend on level of the CNVSS pin. X : Not fixed Since the initial values for other than above mentioned registers and RAM contents are indefinite at reset, they must be set. (67) Processor status register (68) Program counter 0FFF16 (PS) (PCH) (PCL)
X XXXX1 XX
FFFD16 contents FFFC16 contents
Fig. 57 Internal status at reset
57
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
CLOCK GENERATING CIRCUIT
The 3886 group has two built-in oscillation circuits. An oscillation circuit can be formed by connecting a resonator between XIN and XOUT (XCIN and XCOUT). Use the circuit constants in accordance with the resonator manufacturer's recommended values. No external resistor is needed between XIN and XOUT since a feed-back resistor exists on-chip. However, an external feed-back resistor is needed between XCIN and XCOUT. Immediately after power on, only the XIN oscillation circuit starts oscillating, and XCIN and XCOUT pins function as I/O ports.
(2) Wait mode
If the WIT instruction is executed, the internal clock stops at an "H" level, but the oscillator does not stop. The internal clock restarts at reset or when an interrupt is received. Since the oscillator does not stop, normal operation can be started immediately after the clock is restarted.
Frequency Control (1) Middle-speed mode
The internal clock is the frequency of XIN divided by 8. After reset, this mode is selected.
XCIN Rf
XCOUT Rd CCOUT
XIN
XOUT
(2) High-speed mode
The internal clock is half the frequency of XIN.
CCIN
CIN
COUT
(3) Low-speed mode
The internal clock is half the frequency of XCIN. sNote If you switch the mode between middle/high-speed and lowspeed, stabilize both XIN and XCIN oscillations. The sufficient time is required for the sub clock to stabilize, especially immediately after power on and at returning from stop mode. When switching the mode between middle/high-speed and low-speed, set the frequency on condition that f(XIN) > 3f(XCIN).
Fig. 58 Ceramic resonator circuit
XCIN
XCOUT Open
XIN
XOUT Open
External oscillation circuit VCC VSS
External oscillation circuit VCC VSS
(4) Low power dissipation mode
The low power consumption operation can be realized by stopping the main clock XIN in low-speed mode. To stop the main clock, set bit 5 of the CPU mode register to "1." When the main clock XIN is restarted (by setting the main clock stop bit to "0"), set sufficient time for oscillation to stabilize.
Fig. 59 External clock input circuit
Oscillation Control (1) Stop mode
If the STP instruction is executed, the internal clock stops at an "H" level, and XIN and XCIN oscillators stop. When the oscillation stabilizing time set after STP instruction released bit is "0," the prescaler 12 is set to "FF16" and timer 1 is set to "0116." When the oscillation stabilizing time set after STP instruction released bit is "1," set the sufficient time for oscillation of used oscillator to stabilize since nothing is set to the prescaler 12 and timer 1. Either XIN or XCIN divided by 16 is input to the prescaler 12 as count source, and the output of the prescaler 12 is connected to timer 1. Set the timer 1 interrupt enable bit to disabled ("0") before executing the STP instruction. Oscillator restarts when an external interrupt is received, but the internal clock is not supplied to the CPU (remains at "H") until timer 1 underflows. The internal clock is supplied for the first time, when timer 1 underflows. Therefore make sure not to set the timer 1 interrupt request bit to "1" before the STP instruction stops the oscillator. When the oscillator is restarted by reset, apply "L" level to the RESET pin until the oscillation is stable since a wait time will not be generated.
58
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
XCIN
XCOUT
"1"
"0"
Port XC switch bit
XIN
XOUT
Main clock division ratio selection bits (Note) Low-speed mode
1/2
High-speed or middle-speed mode
1/4
1/2
Prescaler 12 FF16
Timer 1
Reset or
0116 STP instruction
Main clock division ratio selection bits (Note) Middle-speed mode High-speed or low-speed mode Main clock stop bit
Timing (internal clock)
Q
S R
STP instruction WIT instruction
SQ R
QS R
STP instruction
Reset Interrupt disable flag l Interrupt request
Note: Either high-speed, middle-speed or low-speed mode is selected by bits 7 and 6 of the CPU mode register. When low-speed mode is selected, set port Xc switch bit (b4) to "1".
Fig. 60 System clock generating circuit block diagram (Single-chip mode)
59
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Reset
Middle-speed mode (f()=1.25 MHz) CM7=0 CM6=1 CM5=0(10 MHz oscillating) CM4=0(32 kHz stopped)
CM6 "1""0"
High-speed mode (f()=5 MHz) CM7=0 CM6=0 CM5=0(10 MHz oscillating) CM4=0(32 kHz stopped)
C M " 0" "1 M6 " C " "1
4
" "0
C "0 M4 C M " "1 6 " 1" " "0 "
CM4 "1""0"
Middle-speed mode (f()=1.25 MHz) CM7=0 CM6=1 CM5=0(10 MHz oscillating) CM4=1(32 kHz oscillating)
CM6 "1""0"
High-speed mode (f()=5 MHz) CM7=0 CM6=0 CM5=0(10 MHz oscillating) CM4=1(32 kHz oscillating)
CM7=1 CM6=0 CM5=0(10 MHz oscillating) CM4=1(32 kHz oscillating)
CM7 "1""0"
Low-speed mode (f()=16 kHz)
C "0 M7 CM " "1 6 "1 " " "0 "
CM4 "1""0"
b7
b4 CPU mode register (CPUM : address 003B16)
CM4 : Port Xc switch bit 0 : I/O port function (stop oscillating) 1 : XCIN-XCOUT oscillating function CM5 : Main clock (XIN- XOUT) stop bit 0 : Operating 1 : Stopped CM7, CM6: Main clock division ratio selection bit b7 b6 0 0 : = f(XIN)/2 ( High-speed mode) 0 1 : = f(XIN)/8 (Middle-speed mode) 1 0 : = f(XCIN)/2 (Low-speed mode) 1 1 : Not available
CM7=1 CM6=0 CM5=1(10 MHz stopped) CM4=1(32 kHz oscillating)
Notes 1 : Switch the mode by the allows shown between the mode blocks. (Do not switch between the modes directly without an allow.) 2 : The all modes can be switched to the stop mode or the wait mode and return to the source mode when the stop mode or the wait mode is ended. 3 : Timer operates in the wait mode. 4 : When the stop mode is ended, a delay of approximately 1 ms occurs by connecting prescaler 12 and Timer 1 in middle/high-speed mode. 5 : When the stop mode is ended, a delay of approximately 0.25 s occurs by Timer 1 and Timer 2 in low-speed mode. 6 : Wait until oscillation stabilizes after oscillating the main clock XIN before the switching from the low-speed mode to middle/high-speed mode. 7 : The example assumes that 10 MHz is being applied to the XIN pin and 32 kHz to the XCIN pin. indicates the internal clock.
Fig. 61 State transitions of system clock
60
CM5 "1""0"
Low-speed mode (f()=16 kHz)
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PROCESSOR MODE
Single-chip mode, memory expansion mode, and microprocessor mode in the M38867M8A/E8A can be selected by changing the contents of the processor mode bits (CM0 and CM1 : b1 and b0 of address 003B16). In memory expansion mode and microprocessor mode, memory can be expanded externally through ports P0 to P3. In these modes, ports P0 to P3 lose their I/O port functions and become bus pins. Table 15 Port functions in memory expansion mode and microprocessor mode Port Name Port P0 Port P1 Port P2 Port P3 Function Outputs low-order 8 bits of address. Outputs high-order 8 bits of address. Operates as I/O pins for data D7 to D0 (including instruction code). P30 and P31 function only as output pins (except that the port latch cannot be read). P32 is the ONW input pin. P33 is the RESETOUT output pin. (Note) P34 is the output pin. P35 is the SYNC output pin. P36 is the WR output pin, and P37 is the RD output pin.
* XXXX16
000016 000816
SFR area
000016 000816
SFR area
004016
Internal RAM reserved area
004016
Internal RAM reserved area
* XXXX16
* YYYY16
Internal ROM
FFFF16
Memory expansion mode
FFFF16
Microprocessor mode
The shaded area are external memory area. *: XXXX16 indicates the last address of internal RAM. YYYY16 indicates the first address of internal ROM.
Note : If CNVSS is connected to VSS, the microcomputer goes to singlechip mode after a reset, so that this pin cannot be used as the RESETOUT output pin.
(1) Single-chip mode
Select this mode by resetting the microcomputer with CNVSS connected to VSS.
Fig. 62 Memory maps in various processor modes
(2) Memory expansion mode
Select this mode by setting the processor mode bits (b1, b0) to "01" in software with CNVSS connected to VSS. This mode enables external memory expansion while maintaining the validity of the internal ROM. However, do not set this mode in the M38869M8A/MCA/MFA and the flash memory version.
b7
b0
CPU mode register (CPUM : address 003B16) Processor mode bits (CM1, CM0)
b1 b0
0 0 1 1
0: Single-chip mode 1: Memory expansion mode (Note) 0: Microprocessor mode (Note) 1: Not available
(3) Microprocessor mode
Select this mode by resetting the microcomputer with CNVSS connected to VCC, or by setting the processor mode bits to "10" in software with CNVSS connected to VSS. In microprocessor mode, the internal ROM is no longer valid and external memory must be used. Do not set this mode in the M38869M8A/MCA/MFA and the flash memory version.
Stack page selection bit 0: 0 page 1: 1 page
Note: This is not available for the products except M38867M8A/E8A.
Fig. 63 Structure of CPU mode register
61
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
BUS CONTROL AT MEMORY EXPANSION
The M38867M8A/E8A have a built-in ONW function to facilitate access to an external (expanded) memory and I/O devices in memory expansion mode or microprocessor mode. If an "L" level signal is input to the P32/ONW pin when the CPU is in a read or write state, the corresponding read or write cycle is extended by one cycle of . During this extended term, the RD and WR signals remain at "L." This extension function is valid only for writing to and reading from addresses 000016 to 000716 and 044016 to FFFF16, and only read and write cycles are extended.
Read cycle
Dummy cycle Write cycle
Read cycle Dummy cycle
Write cycle
AD15--AD0 RD WR ONW
*
*
*
* Term where ONW input signal is received. During this term, the ONW signal must be fixed at either "H" or "L". At all other times, the input level of the ONW signal has no affect on operations. The bus cycles is not extended for an address in the area 000816 to 043F16, because the ONW signal is not received.
Fig. 64 ONW function timing
62
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
EPROM MODE
The built-in PROM of the blank One Time PROM version and builtin EPROM version can be read or programmed with a general-purpose PROM programmer using a special programming adapter. The One Time PROM version and the built-in EPROM version have the function of the M5M27C101 corresponding for writing to the built-in PROM. Set the address of PROM programmer in the user ROM area. Table 16 Programming adapter Package 80P6Q-A 80D0 Name of Programming Adapter PCA4738H-80A PCA4738L-80A
Table 17 PROM programmer setup PROM programmer setup Product name Corresponding device Writing area 0808016 | 0FFFD16 ROM area of microcomputer 808016 | FFFD16
M38867E8AHP M5M27C101K byte program M38867E8AFS
The PROM of the blank One Time PROM version is not tested or screened in the assembly process and following processes. To ensure proper operation after programming, the procedure shown in Figure 65 is recommended to verify programming.
Programming with PROM programmer
Screening (Caution) (150 C for 40 hours)
Verification with PROM programmer
Functional check in target device Caution : The screening temperature is far higher than the storage temperature. Never expose to 150 C exceeding 100 hours.
Fig. 65 Programming and testing of One Time PROM version
63
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
FLASH MEMORY MODE
The M38869FFAHP/GP has the flash memory mode in addition to the normal operation mode (microcomputer mode). The user can use this mode to perform read, program, and erase operations for the internal flash memory. The M38869FFAHP/GP has three modes the user can choose: the parallel input/output and serial input/output mode, where the flash memory is handled by using the external programmer, and the CPU reprogramming mode, where the flash memory is handled by the central processing unit (CPU). The following explains these modes.
Functional Outline (parallel input/output mode)
In the parallel input/output mode, the M38869FFAHP/GP allow the user to choose an operation mode between the read-only mode and the read/write mode (software command control mode) depending on the voltage applied to the VPP pin. When VPP = VPPL, the read-only mode is selected, and the user can choose one of three states (e.g., read, output disable, or standby) depending on ___ ___ ___ inputs to the CE, OE, and WE pins. When VPP = VPPH, the read/ write mode is selected, and the user can choose one of four states (e.g., read, output disable, standby, or write) depending on inputs __ __ ___ to the CE, OE, and WE pins. Table 19 shows assignment states of control input and each state. q Read __ The microcomputer enters the read state by driving the CE, and __ ___ OE pins low and the WE pin high; and the contents of memory corresponding to the address to be input to address input pins (A0-A16). are output to the data input/output pins (D0-D7). q Output disable The microcomputer enters the output disable state by driving the __ ___ __ CE pin low and the WE and OE pins high; and the data input/output pins enter the floating state. q Standby __ The microcomputer enters the standby state by driving the CE pin high. the M38869FFAHP/GP is placed in a power-down state consuming only a minimal supply current. At this time, the data input/ output pins enter the floating state. q Write The microcomputer enters the write state by driving the VPP pin ___ __ high (VPP = VPPH) and then the WE pin low when the CE pin is __ low and the OE pin is high. In this state, software commands can be input from the data input/output pins, and the user can choose program or erase operation depending on the contents of this software command.
(1) Flash memory mode 1 (parallel I/O mode)
The parallel I/O mode can be selected by connecting wires as shown in Figures 65 and supplying power to the VCC and VPP pins. In this mode, the M38869FFAHP/GP operates as an equivalent of MITSUBISHI's CMOS flash memory M5M28F101. However, because the M38869FFAHP/GP's internal memory has a capacity of 60 Kbytes, programming is available for addresses 0100016 to 0FFFF16, and make sure that the data in addresses 0000016 to 00FFF16 and addresses 1000016 to 1FFFF16 are FF16. Note also that the M38869FFAHP/GP does not contain a facility to read out a device identification code by applying a high voltage to address input (A9). Be careful not to erratically set program conditions when using a general-purpose PROM programmer. Table 18 shows the pin assignments when operating in the parallel input/output mode.
Table 18
Pin assignments of M38869FFAHP/GP when operating in the parallel input/output mode M38869FFAHP/GP VCC CNVSS VSS Ports P0, P1, P31 Port P2 P36 P37 P33 M5M28F101 VCC VPP VSS A0-A16 D0-D7 __ CE __ OE ___ WE
VCC VPP VSS Address input Data I/O __ CE ___ OE ___ WE
Table 19 Assignment sates of control input and each state Pin Mode Read-only State Read Output disable Standby Read Output disable Standby Write
__ __ ___
CE VIL VIL VIH VIL VIL VIH VIL
OE VIL VIH x VIL VIH x VIH
WE VIH VIH x VIH VIH x VIL
VPP VPPL VPPL VPPL VPPH VPPH VPPH VPPH
Data I/O Output Floating Floating Output Floating Floating Input
Read/Write
Note: x can be VIL or VIH.
64
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 20 Pin description (flash memory parallel I/O mode) Pin VCC, VSS CNVSS _____ RESET XIN XOUT AVSS VREF P00-P07 P10-P17 P20-P27 P30-P37 Name Power supply VPP input Reset input Clock input Clock output Analog supply input Reference voltage input Address input (A0-A7) Address input (A8-A15) Data I/O (D0-D7) Control signal input Input /Output -- Input Input Input Output -- Input Input Input I/O Input Functions Supply 5 V 10 % to VCC and 0 V to VSS. Connect to 5 V 10 % in read-only mode, connect to 11.7 to 12.6 V in read/write mode. Connect to VSS. Connect a ceramic resonator between XIN and XOUT. Connect to VSS. Connect to VSS. Port P0 functions as 8-bit address input (A0-A7). Port P1 functions as 8-bit address input (A8-A15). Function as 8-bit data's I/O pins (D0-D7). ___ __ __ P37, P36 and P33 function as the OE, CE and WE input pins respectively. P31 functions as the A16 input pin. Connect P30 and P32 to VSS. Input "H" or "L" to P34, P35, or keep them open. Connect P44, P46 to VSS. Input "H" or "L" to P40 - P43, P45, P47, or keep them open. Input "H" or "L", or keep them open. Input "H" or "L", or keep them open. Input "H" or "L", or keep them open. Input "H" or "L", or keep them open.
P40-P47 P50-P57 P60-P67 P70-P77 P80-P87
Input port P4 Input port P5 Input port P6 Input port P7 Input port P8
Input Input Input Input Input
65
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
WE
A10
A11
A12
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
A16
P32 P33 P34 P35 P36 P37 P00/P3REF P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13 P14 P15
A13
CE
OE
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
Vcc
P31/PWM10 P30/PWM00 P87/DQ7 P86/DQ6 P85/DQ5 P84/DQ4 P83/DQ3 P82/DQ2 P81/DQ1 P80/DQ0 VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3 P62/AN2 P61/AN1
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
40 39 38 37 36 35 34 33
M38869FFAHP M38869FFAGP
32 31 30 29 28 27 26 25 24 23 22 21
P16 P17 P20 P21 P22 P23 P24 P25 P26 P27 VSS XOUT XIN P40/XCOUT P41/XCIN RESET CNVSS P42/INT0/OBF00 P43/INT1/OBF01 P44/RXD
A14 A15 D0 D1 D2 D3 D4 D5 D6 D7 V ss
*
Vpp
Fig. 66
Pin connection of M38869FFAHP/GP when operating in parallel input/output mode
66
P60/AN0 P77/SCL P76/SDA P75/INT41 P74/INT31 P73/SRDY2/INT21 P72/SCLK2 P71/SOUT2 P70/SIN2 P57/DA2/PWM11 P56/DA1/PWM01 P55/CNTR1 P54/CNTR0 P53/INT40/W P52/INT30/R P51/INT20/S0 P50/A0 P47/SRDY1/S1 P46/SCLK1/OBF10 P45/TXD
er c os in * :Connndeictattosththecelaamimemcoilrlatpoin.circuit. i ce f sh y
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Read-only Mode
The microcomputer enters the read-only mode by applying VPPL to the VPP pin. In this mode, the user can input the address of a memory location to be read and the control signals at the timing
shown in Figure 67, and the M38869FFAHP/GP will output the contents of the user's specified address from data I/O pin to the external. In this mode, the user cannot perform any operation other than read.
VIH Address VIL tRC VIH CE VIL ta(CE) VIH OE VIL VIH WE VIL VOH Data VOL Floating ta(OE) tOLZ tCLZ ta(AD) Dout tDH Floating tWRR tDF Valid address
Fig. 67 Read timing
Read/Write Mode
The microcomputer enters the read/write mode by applying VPPH to the VPP pin. In this mode, the user must first input a software command to choose the operation (e. g., read, program, or erase) to be performed on the flash memory (this is called the first cycle), and then input the information necessary for execution of the command (e.g, address and data) and control signals (this is called the second cycle). When this is done, the M38869FFAHP/GP executes the specified operation. Table 21 Software command (Parallel input/output mode) Symbol Read Program Program verify Erase Erase verify Reset Device identification First cycle Address input x x x x Verify address x x
Table 21 shows the software commands and the input/output information in the first and the second cycles. The input address is ___ latched internally at the falling edge of the WE input; software commands and other input data are latched internally at the rising ___ edge of the WE input. The following explains each software command. Refer to Figures 68 to 70 for details about the signal input/output timings.
Data input 0016 4016 C016 2016 A016 FF16 9016
Second cycle Address input Data I/O Read address Read data (Output) Program address Program data (Input) x Verify data (Output) x 2016 (Input) x Verify data (Output) x FF16 (Input) ADI DDI (Output)
Note: ADI = Device identification address : manufacturer's code 0000016, device code 0000116 DDI = Device identification data : manufacturer's code 1C16, device code D016 X can be VIL or VIH.
67
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
q Read command The microcomputer enters the read mode by inputting command code "0016" in the first cycle. The command code is latched into ___ the internal command latch at the rising edge of the WE input. When the address of a memory location to be read is input in the second cycle, with control signals input at the timing shown in Figure 68, the M38869FFAHP/GP outputs the contents of the specified address from the data I/O pins to the external.
The read mode is retained until any other command is latched into the command latch. Consequently, once the M38869FFAHP/GP enters the read mode, the user can read out the successive memory contents simply by changing the input address and executing the second cycle only. Any command other than the read command must be input beginning from its command code over again each time the user execute it. The contents of the command latch immediately after power-on is 0016.
VIH Address VIL tWC VIH CE VIL tCS VIH OE VIL tRRW VIH WE VIL ta(OE) tDS VIH Data VIL tVSC VPPH VPP VPPL 0016 tDH tOLZ tCLZ ta(AD) Dout tDH tWP tWRR tDF tCH ta(CE) tRC Valid address
Fig. 68 Timings during reading
68
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
q Program command The microcomputer enters the program mode by inputting command code "4016" in the first cycle. The command code is latched ___ into the internal command latch at the rising edge of the WE input. When the address which indicates a program location and data is input in the second cycle, the M38869FFAHP/GP internally ___ latches the address at the falling edge of the WE input and the ___ data at the rising edge of the WE input. The M38869FFAHP/GP ___ starts programming at the rising edge of the WE input in the second cycle and finishes programming within 10 s as measured by its internal timer. Programming is performed in units of bytes. Note: A programming operation is not completed by executing the program command once. Always be sure to execute a program verify command after executing the program command. When the failure is found in this verification, the user must repeatedly execute the program command until the pass. Refer to Figure 71 for the programming flowchart.
q Program verify command The microcomputer enters the program verify mode by inputting command code "C016" in the first cycle. This command is used to verify the programmed data after executing the program command. The command code is latched into the internal command ___ latch at the rising edge of the WE input. When control signals are input in the second cycle at the timing shown in Figure 69, the M38869FFAHP/GP outputs the programmed address's contents to the external. Since the address is internally latched when the program command is executed, there is no need to input it in the second cycle.
VIH Address VIL tWC VIH CE VIL tCS tCH VIH OE VIL tRRW tWP VIH WE VIL tDS VIH Data VIL tVSC VPPH VPP VPPL 4016 tDH
Program verify Program address tAS tAH Program
tCS tCH
tCS tCH
tWPH
tWP
tDP
tWP
tWRR
tDS
tDS
DIN tDH
C016 tDH
Dout Verify data output
Fig. 69 Input/output timings during programming (Verify data is output at the same timing as for read.)
69
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
q Erase command The erase command is executed by inputting command code 2016 in the first cycle and command code 2016 again in the second cycle. The command code is latched into the internal command ___ latch at the rising edges of the WE input in the first cycle and in the second cycle, respectively. The erase operation is initiated at ___ the rising edge of the WE input in the second cycle, and the memory contents are collectively erased within 9.5 ms as measured by the internal timer. Note that data 0016 must be written to all memory locations before executing the erase command. Note: An erase operation is not completed by executing the erase command once. Always be sure to execute an erase verify command after executing the erase command. When the failure is found in this verification, the user must repeatedly execute the erase command until the pass. Refer to Figure 71 for the erase flowchart.
q Erase verify command The user must verify the contents of all addresses after completing the erase command. The microcomputer enters the erase verify mode by inputting the verify address and command code A016 in the first cycle. The address is internally latched at the fall___ ing edge of the WE input, and the command code is internally ___ latched at the rising edge of the WE input. When control signals are input in the second cycle at the timing shown in Figure 70, the M38869FFAHP/GP outputs the contents of the specified address to the external. Note: If any memory location where the contents have not been erased is found in the erase verify operation, execute the operation of "erase erase verify" over again. In this case, however, the user does not need to write data 0016 to memory locations before erasing.
VIH Address VIL tWC VIH CE VIL tCS tCH VIH OE VIL tRRW tWP VIH WE VIL tDS VIH Data VIL tVSC VPPH VPP VPPL tDH tDH 2016 2016 tDS tWPH tWP tDE tCS tCH Erase
Erase verify Verify address tAS tAH
tCS tCH
tWP
tWRR
tDS
A016
Dout Verify data output
tDH
Fig. 70 Input/output timings during erasing (verify data is output at the same timing as for read.)
70
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
q Reset command The reset command provides a means of stopping execution of the erase or program command safely. If the user inputs command code FF16 in the second cycle after inputting the erase or program command in the first cycle and again input command code FF16 in the third cycle, the erase or program command is disabled (i.e., reset), and the M38869FFAHP/GP is placed in the read mode. If the reset command is executed, the contents of the memory does not change. q Device identification code command By inputting command code 9016 in the first cycle, the user can read out the device identification code. The command code is latched into the internal command latch at the rising edge of the ___ WE input. At this time, the user can read out manufacture's code 1C16 (i.e., MITSUBISHI) by inputting 000016 to the address input pins in the second cycle; the user can read out device code D016 (i. e., 1M-bit flash memory) by inputting 000116. These command and data codes are input/output at the same timing as for read.
71
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Program START
Erase START
VCC = 5 V, VPP = VPPH
VCC = 5 V, VPP = VPPH
ADRS = first location
YES
ALL BYTES = 0016 ? NO
X=0 WRITE PROGRAM COMMAND WRITE PROGRAM DATA DURATION = 10 s X=X+1 WRITE PROGRAM-VERIFY COMMAND DURATION = 6 s YES X = 25 ? NO FAIL PASS VERIFY BYTE ? PASS NO INC ADRS LAST ADRS ? NO YES WRITE READ COMMAND 0016 FAIL VERIFY BYTE ? FAIL
4016
PROGRAM ALL BYTES = 0016
ADRS = first location DIN X=0 WRITE ERASE COMMAND WRITE ERASE COMMAND DURATION = 9.5 ms X=X+1 WRITE ERASE-VERIFY COMMAND DURATION = 6 s
2016
C016
2016
A016
X = 1000 ?
YES
PASS VERIFY BYTE ? PASS VERIFY BYTE ? FAIL
VPP = VPPL INC ADRS DEVICE PASSED DEVICE FAILED
NO LAST ADRS ? YES WRITE READ COMMAND 0016
VPP = VPPL
DEVICE PASSED
DEVICE FAILED
Fig. 71 Programming/Erasing algorithm flow chart
72
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 22 DC ELECTRICAL CHARACTERISTICS (Ta = 25 C, VCC = 5 V 10 %, unless otherwise noted) Symbol ISB1 ISB2 ICC1 ICC2 ICC3 IPP1 IPP2 IPP3 VIL VIH VOL VOH1 VOH2 VPPL VPPH VCC supply current (at standby) VCC supply current (at read) VCC supply current (at program) VCC supply current (at erase) VPP supply current (at read) VPP supply current (at program) VPP supply current (at erase) "L" input voltage "H" input voltage "L" output voltage "H" output voltage VPP supply voltage (read only) VPP supply voltage (read/write) Parameter Test conditions
__
Min.
Limits Typ.
VCC = 5.5 V, CE = VIH VCC = 5.5 V, __ CE = VCC 0.2 V __ VCC = 5.5 V, CE = VIL, tRC = 150 ns, IOUT = 0 mA VPP = VPPH VPP = VPPH 0VPPVCC VCCMax. 1 100 15 15 15 10 100 100 30 30 0.8 VCC 0.45
Unit mA A mA mA mA A A A mA mA V V V V V V V
12.0
VCC + 1.0 12.6
AC ELECTRICAL CHARACTERISTICS (Ta = 25 C, VCC = 5 V 10 %, unless otherwise noted) Table 23 Read-only mode Symbol tRC ta(AD) ta(CE) ta(OE) tCLZ tOLZ tDF tDH tWRR Parameter Read cycle time Address access time __ CE access time __ OE access time __ Output enable time (after CE) __ Output enable time (after OE) __ Output floating time (after OE) __ __ Output valid time (after CE, OE, address) Write recovery time (before read) Limits Min. 250 Max. 250 250 100 0 0 35 0 6 Unit ns ns ns ns ns ns ns ns s
Table 24 Read/Write mode Symbol tWC tAS tAH tDS tDH tWRR tRRW tCS tCH tWP tWPH tDP tDE tVSC Write cycle time Address set up time Address hold time Data setup time Data hold time Write recovery time (before read) Read recovery time (before write) __ CE setup time __ CE hold time Write pulse width Write pulse waiting time Program time Erase time VPP setup time Parameter Limits Min. 150 0 60 50 10 6 0 20 0 60 20 10 9.5 1 Max. Unit ns ns ns ns ns s s ns ns ns ns s ms s
Note: Read timing of Read/Write mode is same as Read-only mode.
73
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(2) Flash memory mode 2 (serial I/O mode)
The M38869FFAHP/GP has a function to serially input/output the software commands, addresses, and data required for operation on the internal flash memory (e. g., read, program, and erase) using only a few pins. This is called the serial I/O (input/output) mode. This mode can be selected by driving the SDA (serial data __ input/output), SCLK (serial clock input ), and OE pins high after
connecting wires as shown in Figures 72 and powering on the VCC pin and then applying VPPH to the VPP pin. In the serial I/O mode, the user can use six types of software commands: read, program, program verify, erase, erase verify and error check. Serial input/output is accomplished synchronously with the clock, beginning from the LSB (LSB first).
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
P32 P33 P34 P35 P36 P37 P00/P3REF P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13 P14 P15
OE
Vcc
P31/PWM10 P30/PWM00 P87/DQ7 P86/DQ6 P85/DQ5 P84/DQ4 P83/DQ3 P82/DQ2 P81/DQ1 P80/DQ0 VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3 P62/AN2 P61/AN1
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
M38869FFAHP M38869FFAGP
P16 P17 P20 P21 P22 P23 P24 P25 P26 P27 VSS XOUT XIN P40/XCOUT P41/XCIN RESET CNVSS P42/INT0/OBF00 P43/INT1/OBF01 P44/RXD
Vss
*
Vpp
SDA
c am cl * :Coninecctatoetshteheefrlashicmoesmiolraytionn.circuit. ndi t pi
Fig. 72 Pin connection of M38869FFAHP/GP when operating in serial I/O mode
74
BUSY
SCLK
P60/AN0 P77/SCL P76/SDA P75/INT41 P74/INT31 P73/SRDY2/INT21 P72/SCLK2 P71/SOUT2 P70/SIN2 P57/DA2/PWM11 P56/DA1/PWM01 P55/CNTR1 P54/CNTR0 P53/INT40/W P52/INT30/R P51/INT20/S0 P50/A0 P47/SRDY1/S1 P46/SCLK1/OBF10 P45/TXD
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 25 Pin description (flash memory serial I/O mode) Pin VCC, VSS CNVSS _____ RESET XIN XOUT AVSS VREF P00-P07 P10-P17 P20-P27 P30-P36 P37 P40-P43, P45 P44 P46 P47 P50-P57 P60-P67 P70-P77 P80-P87 Name Power supply VPP input Reset input Clock input Clock output Analog supply input Reference voltage input Input port P0 Input port P1 Input port P2 Input port P3 Control signal input Input port P4 SDA I/O SCLK input BUSY output Input port P5 Input port P6 Input port P7 Input port P8 Input /Output -- Input Input Input Output -- Input Input Input Input Input Input Input I/O Input Output Input Input Input Input Functions Supply 5 V 10 % to VCC and 0 V to VSS. Connect to 11.7 to 12.6 V. Connect to VSS. Connect a ceramic resonator between XIN and XOUT. Connect to VSS. Input an arbitrary level between the range of VSS and VCC. Input "H" or "L", or keep them open. Input "H" or "L", or keep them open. Input "H" or "L", or keep them open. Input "H" or "L", or keep them open.
__
OE input pin Input "H" or "L" to P40 - P43, P45, or keep them open. This pin is for serial data I/O. This pin is for serial clock input. This pin is for BUSY signal output. Input "H" or "L", or keep them open. Input "H" or "L", or keep them open. Input "H" or "L", or keep them open. Input "H" or "L", or keep them open.
75
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Functional Outline (serial I/O mode)
In the serial I/O mode, data is transferred synchronously with the clock using serial input/output. The input data is read from the SDA pin into the internal circuit synchronously with the rising edge of the serial clock pulse; the output data is output from the SDA pin synchronously with the falling edge of the serial clock pulse.
Data is transferred in units of eight bits. In the first transfer, the user inputs the command code. This is followed by address input and data input/output according to the contents of the command. Table 26 shows the software commands used in the serial I/O mode. The following explains each software command.
Table 26 Software command (serial I/O mode) Number of transfers First command Command code input Read 0016 Program 4016 Program verify C016 Erase 2016 Erase verify A016 Error check 8016 Second Read address L (Input) Program address L (Input) Verify data (Output) 2016 (Input) Verify address L (Input) Error code (Output) Third Read address H (Input) Program address H (Input) ---------- ---------- Verify address H (Input) ---------- Fourth Read data (Output) Program data (Input) ---------- ---------- Verify data (Output) ----------
q Read command Input command code 0016 in the first transfer. Proceed and input the low-order 8 bits and the high-order 8 bits of the address and __ pull the OE pin low. When this is done, the M38869FFAHP/GP reads out the contents of the specified address, and then latchs it
__
into the internal data latch. When the OE pin is released back high and serial clock is input to the SCLK pin, the read data that has been latched into the data latch is serially output from the SDA pin.
tCH SCLK A0 SDA A7
tCH
A8
A15
D0
D7
00000000 Command code input (0016) Read address input (L)
Read address input (H) tCR
tWR
tRC
Read data output
OE Read BUSY "L" Note : When outputting the read data, the SDA pin is switched for output at the first falling edge of SCLK. The SDA pin is placed in the floating state during the period of th(C-E) after the last rising edge of SCLK (at the 8th bit).
Fig. 73 Timings during reading
76
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
q Program command Input command code 4016 in the first transfer. Proceed and input the low-order 8 bits and the high-order 8 bits of the address and then program data. Programming is initiated at the last rising edge of the serial clock during program data transfer. The BUSY pin is driven high during program operation. Programming is completed within 10 s as measured by the internal timer, and the BUSY pin is pulled low.
Note : A programming operation is not completed by executing the program command once. Always be sure to execute a program verify command after executing the program command. When the failure is found in the verification, the user must repeatedly execute the program command until the pass in the verification. Refer to Figure 71 for the programming flowchart.
tCH SCLK
tCH
tCH
tPC A0 SDA 00000010 Command code input (4016) A7 A8 A15 D0 D7
Program address input (L) Program address input (H)
Program data input
OE
tWP Program
BUSY
Fig. 74 Timings during programming
q Program verify command Input command code C016 in the first transfer. Proceed and drive __ the OE pin low. When this is done, The M38869FFAHP/GP verifyreads the programmed address's contents, and then latchs it into
__
the internal data latch. When the OE pin is released back high and serial clock is input to the SCLK pin, the verify data that has been latched into the data latch is serially output from the SDA pin.
SCLK D0 SDA 00000011 Command code input (C016) tCRPV OE Verify read BUSY "L" tWR tRC D7
Verify data output
Note: When outputting the verify data, the SDA pin is switched for output at the first falling edge of SCLK. The SDA pin is placed in the floating state during the period of th(C-E) after the last rising edge of SCLK (at the 8th bit).
Fig. 75 Timings during program verify
77
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
q Erase command Input command code 2016 in the first transfer and command code 2016 again in the second transfer. When this is done, the M38869FFAHP/GP executes an erase command. Erase is initiated at the last rising edge of the serial clock. The BUSY pin is driven high during the erase operation. Erase is completed within 9.5 ms as measured by the internal timer, and the BUSY pin is pulled low. Note that data 0016 must be written to all memory loca-
tions before executing the erase command. Note: A erase operation is not completed by executing the erase command once. Always be sure to execute a erase verify command after executing the erase command. When the failure is found in the verification, the user must repeatedly execute the erase command until the pass in the verification. Refer to Figure 71 for the erase flowchart.
tCH SCLK tEC SDA 00000100 00000100 Command code input (2016) Command code input (2016) "H" OE twE BUSY Erase
Fig. 76 Timings at erasing
q Erase verify command The user must verify the contents of all addresses after completing the erase command. Input command code A016 in the first transfer. Proceed and input the low-order 8 bits and the high-order __ 8 bits of the address and pull the OE pin low. When this is done, the M38869FFAHP/GP reads out the contents of the specified ad__ dress, and then latchs it into the internal data latch. When the OE pin is released back high and serial clock is input to the SCLK pin,
the verify data that has been latched into the data latch is serially output from the SDA pin. Note: If any memory location where the contents have not been erased is found in the erase verify operation, execute the operation of "erase erase verify" over again. In this case, however, the user does not need to write data 0016 to memory locations before erasing.
tCH SCLK A0 SDA A7
tCH
A8
A15
D0
D7
00000101 Command code input (A016) Verify address input (L)
Verify address input (H) tCREV
tWR
tRC
Verify data output
OE Verify read BUSY "L" Note : When outputting the verify data, the SDA pin is switched for output at the first falling edge of SCLK. The SDA pin is placed in the floating state during the period of th(C-E) after the last rising edge of SCLK (at the 8th bit).
Fig. 77 Timings during erase verify
78
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
q Error check command Input command code 8016 in the first transfer, and the M38869FFAHP/GP outputs error information from the SDA pin, beginning at the next falling edge of the serial clock. If the LSB bit of the 8-bit error information is 1, it indicates that a command error has occurred. A command error means that some invalid commands other than commands shown in Table 26 has been input. When a command error occurs, the serial communication circuit sets the corresponding flag and stops functioning to avoid an erroneous programming or erase. When being placed in this state, the serial communication circuit does not accept the subsequent serial clock and data (even including an error check command). Therefore, if the user wants to execute an error check command,
temporarily drop the VPP pin input to the VPPL level to terminate the serial input/output mode. Then, place the M38869FFAHP/GP into the serial I/O mode back again. The serial communication circuit is reset by this operation and is ready to accept commands. The error flag alone is not cleared by this operation, so the user can examine the serial communication circuit's error conditions before reset. This examination is done by the first execution of an error check command after the reset. The error flag is cleared when the user has executed the error check command. Because the error flag is undefined immediately after power-on, always be sure to execute the error check command.
tCH SCLK E0 SDA 00000001 Command code input (8016) "H" ??????? Error flag output
OE
BUSY "L"
Note: When outputting the error flag, the SDA pin is switched for output at the first falling edge of the serial clock. The SDA pin is placed in the floating state during the period of th(C-E) after the last rising edge of the serial clock (at the 8th bit).
Fig. 78 Timings at error checking Note: The programming/erasing algorithm flow chart of the serial I/O mode is the same as that of the parallel I/O mode. Refer to Figure 71.
79
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
DC ELECTRICAL CHARACTERISTICS (Ta = 25 C, VCC = 5 V 10 %, VPP = 11.7 to 12.6 V, unless otherwise noted)
ICC, IPP-relevant standards during read, program, and erase are the same as in the parallel input/output mode. VIH, VIL, VOH, VOL, IIH, and __ IIL for the SCLK, SDA, BUSY, OE pins conform to the microcomputer modes.
Table 27 AC Electrical characteristics (Ta = 25 C, VCC = 5 V 10 %, VPP = 11.7 to 12.6 V, f(XIN) = 10 MHz, unless otherwise noted) Symbol tCH tCR tWR tRC tCRPV tWP tPC tCREV tWE tEC tc(CK) tw(CKH) tw(CKL) tr(CK) tf(CK) td(C-Q) th(C-Q) th(C-E) tsu(D-C) th(C-D) Parameter Serial transmission interval Read waiting time after transmission Read pulse width Transfer waiting time after read Waiting time before program verify Programming time Transfer waiting time after programming Waiting time before erase verify Erase time Transfer waiting time after erase SCLK input cycle time SCLK high-level pulse width SCLK low-level pulse width SCLK rise time SCLK fall time SDA output delay time SDA output hold time SDA output hold time (only the 8th bit) SDA input set up time SDA input hold time Limits Min. Max. 500(Note 1) 500(Note 1) 400(Note 2) 500(Note 1) 6 10 500(Note 1) 6 9.5 500(Note 1) 250 100 100 20 20 0 90 0 150(Note 3) 250(Note 4) 30 90 Unit ns ns ns ns s s ns ns ns ns ns ns ns ns ns ns ns ns
Notes 1: When f(XIN) = 10 MHz or less, calculate the minimum value according to formula 1. 5000 x 106 f(XIN) 2: When f(XIN) = 10 MHz or less, calculate the minimum value according to formula 2. Formula 1 : 4000 x 106 f(XIN) 3: When f(XIN) = 10 MHz or less, calculate the minimum value according to formula 3. Formula 2 : 1500 x 106 f(XIN) 4: When f(XIN) = 10 MHz or less, calculate the minimum value according to formula 4 Formula 3 : Formula 4 : 2500 f(XIN) x 106
AC waveforms
tf(CK) tw(CKL)
tc(CK) tr(CK)
tw(CKH)
SCLK th(C-Q) td(C-Q) th(C-E) Test conditions for AC characteristics SDA output * Output timing voltage : VOL = 0.8 V, VOH = 2.0 V tsu(D-C) th(C-D) * Input timing voltage : VIL = 0.2 VCC, VIH = 0.8 VCC
SDA input
80
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(3) Flash memory mode 3 (CPU reprogramming mode)
The M38869FFAHP/GP has the CPU reprogramming mode where a built-in flash memory is handled by the central processing unit (CPU). In CPU reprogramming mode, the flash memory is handled by writing and reading to/from the flash memory control register (see Figure 79) and the flash command register (see Figure 80). The CNVSS pin is used as the VPP power supply pin in CPU reprogramming mode. It is necessary to apply the power-supply voltage of VPPH from the external to this pin.
Functional Outline (CPU reprogramming mode)
Figure 79 shows the flash memory control register bit configuration. Figure 80 shows the flash command register bit configuration. Bit 0 of the flash memory control register is the CPU reprogramming mode select bit. When this bit is set to "1" and VPPH is applied to the CNVss/VPP pin, the CPU reprogramming mode is selected. Whether the CPU reprogramming mode is realized or not is judged by reading the CPU reprogramming mode monitor flag (bit 2 of the flash memory control register). Bit 1 is a busy flag which becomes "1" during erase and program execution.
Whether these operations have been completed or not is judged by checking this flag after each command of erase and the program is executed. Bits 4, 5 of the flash memory control register are the erase/program area select bits. These bits specify an area where erase and program is operated. When the erase command is executed after an area is specified by these bits, only the specified area is erased. Only for the specified area, programming is enabled; for the other areas, programming is disabled. When CPU reprogramming mode is valid, the area where is not specified by the erase/program area select bits cannot be read out. Transfer CPU reprogramming mode control program to internal RAM before entering the CPU reprogramming mode, and then execute this program on internal RAM. If an interrupt occurs while this program is being executed, the flash memory area is accessed, but normally operation cannot be performed because the flash memory area cannot be read out. During CPU reprogramming mode control program execution, execute the processing such as interrupt disabled, etc. Figure 81 shows the CPU mode register bit configuration in the CPU reprogramming mode. Set bits 1 and 0 to "00" (single-chip mode) in the CPU reprogramming mode.
7
6 0
5
4
3 0
2
1
0 Flash memory control regsiter (FCON : address 0FFE16) CPU reprogramming mode select bit (Note) 0 : CPU reprogramming mode is invalid. (Normal operation mode) 1 : When applying 0 V or VPPL to CNVSS/VPP pin, CPU reprogramming mode is invalid. When applying VPPH to CNVSS/VPP pin, CPU reprogramming mode is valid. Erase/Program busy flag 0 : Erase and program are completed or not have been executed. 1 : Erase/program is being executed. CPU reprogramming mode monitor flag 0 : CPU reprogramming mode is invalid. 1 : CPU reprogramming mode is valid. Fix this bit to "0." Erase/Program area select bits 0 0 : Addresses 100016 to FFFF16 (total 60 Kbytes) 0 1 : Addresses 100016 to 7FFF16 (total 28 Kbytes) 1 0 : Addresses 800016 to FFFF16 (total 32 Kbytes) 1 1 : Not available Fix this bit to "0." Not used (returns "0" when read)
Note: Bit 0 can be reprogrammed only when 0 V is applied to the CNVSS/VPP pin.
Fig. 79 Flash memory control register bit configuration
81
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
q CPU reprogramming mode operation procedure The operation procedure in CPU reprogramming mode is described below. < Beginning procedure > Apply 0 V to the CNVss/VPP pin for reset release. After CPU reprogramming mode control program is transferred to internal RAM, jump to this control program on RAM. (The following operations are controlled by this control program). Set "1" to the CPU reprogramming mode select bit. Apply VPPH to the CNVSS/VPP pin. Wait till CNVSS/VPP pin becomes 12 V. Read the CPU reprogramming mode monitor flag to confirm whether the CPU reprogramming mode is valid. The operation of the flash memory is executed by software-command-writing to the flash command register . Note: The following are necessary other than this: *Control for data which is input from the external (serial I/O etc.) and to be programmed to the flash memory *Initial setting for ports etc. *Writing to the watchdog timer
< Release procedure > Apply 0V to the CNVSS/VPP pin. Wait till CNVSS/VPP pin becomes 0V. Set the CPU reprogramming mode select bit to "0." Each software command is explained as follows. q Read command When "0016" is written to the flash command register, the M38869FFAHP/GP enters the read mode. The contents of the corresponding address can be read by reading the flash memory (For instance, with the LDA instruction etc.) under this condition. The read mode is maintained until another command code is written to the flash command register. Accordingly, after setting the read mode once, the contents of the flash memory can continuously be read. After reset and after the reset command is executed, the read mode is set.
b7
b0
7
6
5
4
3
2
1
0 Flash command register (FCMD : address 0FFF16) Writing of software command
0
0
CPU mode register
(CPUM : address 003B16)
Processor mode bits b1 b0 0 0 : Single-chip mode 0 1 : Not available 1 X : Not available Stack page selection bit 0 : 0 page 1 : 1 page Reserved (Do not write "0" to this bit when using XCIN-XCOUT oscillation function.) Port XC switch bit 0 : I/O port function (stop oscillating) 1 : XCIN-XCOUT oscillating function Main clock (XIN-XOUT) stop bit 0 : Oscillating 1 : Stopped Main clock division ratio selection bits b7 b6 0 0 : = f(XIN)/2 (high-speed mode) 0 1 : = f(XIN)/8 (middle-speed mode) 1 0 : = f(XCIN)/2 (low-speed mode) 1 1 : Not available
* Read command * Program command * Program verify command * Erase command * Erase verify command * Reset command
"0016" "4016" "C016" "2016" + "2016" "A016" "FF16" + "FF16"
Note: The flash command register is write-only register.
Fig. 80 Flash command register bit configuration
Fig. 81 CPU mode register bit configuration in CPU rewriting mode
82
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
q Program command When "4016" is written to the flash command register, the M38869FFAHP/GP enters the program mode. Subsequently to this, if the instruction (for instance, STA instruction) for writing byte data in the address to be programmed is executed, the control circuit of the flash memory executes the program. The erase/program busy flag of the flash memory control register is set to "1" when the program starts, and becomes "0" when the program is completed. Accordingly, after the write instruction is executed, CPU can recognize the completion of the program by polling this bit. The programmed area must be specified beforehand by the erase/ program area select bits. During programming, watchdog timer stops with "FFFF16" set. Note: A programming operation is not completed by executing the program command once. Always be sure to execute a program verify command after executing the program command. When the failure is found in this verification, the user must repeatedly execute the program command until the pass. Refer to Figure 82 for the flow chart of the programming. q Program verify command When "C016" is written to the flash command register, the M38869FFAHP/GP enters the program verify mode. Subsequently to this, if the instruction (for instance, LDA instruction) for reading byte data from the address to be verified (i.e., previously programmed address), the contents which has been written to the address actually is read. CPU compares this read data with data which has been written by the previous program command. In consequence of the comparison, if not agreeing, the operation of "program program verify" must be executed again. q Erase command When writing "2016" twice continuously to the flash command register, the flash memory control circuit performs erase to the area specified beforehand by the erase/program area select bits. Erase/program busy flag of the flash memory control register becomes "1" when erase begins, and it becomes "0" when erase completes. Accordingly, CPU can recognize the completion of erase by polling this bit. Data "0016" must be written to all areas to be erased by the program and the program verify commands before the erase command is executed. During erasing, watchdog timer stops with "FFFF16" set. Note: The erasing operation is not completed by executing the erase command once. Always be sure to execute an erase verify command after executing the erase command. When the failure is found in this verification, the user must repeatedly execute the erase command until the pass. Refer to Figure 82 for the erasing flowchart.
q Erase verify command When "A016" is written to the flash command register, the M38869FFAHP/GP enters the erase verify mode. Subsequently to this, if the instruction (for instance, LDA instruction) for reading byte data from the address to be verified, the contents of the address is read. CPU must erase and verify to all erased areas in a unit of address. If the address of which data is not "FF16" (i.e., data is not erased) is found, it is necessary to discontinue erasure verification there, and execute the operation of "erase erase verify" again. Note: By executing the operation of "erase erase verify" again when the memory not erased is found. It is unnecessary to write data "0016" before erasing in this case. q Reset command The reset command is a command to discontinue the program or erase command on the way. When "FF16" is written to the command register two times continuously after "4016" or "2016" is written to the flash command register, the program, or erase command becomes invalid (reset), and the M38869FFAHP/GP enters the reset mode. The contents of the memory does not change even if the reset command is executed.
DC Electric Characteristics
Note: The characteristic concerning the flash memory part are the same as the characteristic of the parallel I/O mode.
AC Electric Characteristics
Note: The characteristics are the same as the characteristic of the microcomputer mode.
83
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Program START
Erase START
ADRS = first location
YES
ALL BYTES = 0016 ? NO
X=0 WRITE PROGRAM COMMAND WRITE PROGRAM DATA
4016
PROGRAM ALL BYTES = 0016
ADRS = first location DIN X=0
WAIT 1s WRITE ERASE COMMAND NO ERASE PROGRAM BUSY FLAG = 0 YES X=X+1 WRITE PROGRAM-VERIFY COMMAND DURATION = 6 s WRITE ERASE COMMAND 2016
2016
WAIT 1s C016
NO
ERASE PROGRAM BUSY FLAG = 0 YES X=X+1
X = 25 ? NO FAIL
YES WRITE ERASE-VERIFY COMMAND PASS DURATION = 6 s A016
VERIFY BYTE ? PASS
VERIFY BYTE ? FAIL
X = 1000 ? INC ADRS NO LAST ADRS ? NO YES WRITE READ COMMAND 0016 PASS DEVICE PASSED DEVICE FAILED NO INC ADRS LAST ADRS ? YES WRITE READ COMMAND FAIL
YES
PASS VERIFY BYTE ? VERIFY BYTE ? FAIL
0016
DEVICE PASSED
DEVICE FAILED
Fig. 82 Flowchart of program/erase operation at CPU reprogramming mode
84
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
NOTES ON PROGRAMMING Processor Status Register
The contents of the processor status register (PS) after a reset are undefined, except for the interrupt disable flag (I) which is "1." After a reset, initialize flags which affect program execution. In particular, it is essential to initialize the index X mode (T) and the decimal mode (D) flags because of their effect on calculations.
Serial I/O
In clock synchronous serial I/O, if the receive side is using an external clock and it is to output the SRDY1 signal, set the transmit enable bit, the receive enable bit, and the SRDY1 output enable bit to "1." Serial I/O1 continues to output the final bit from the TXD pin after transmission is completed. SOUT2 pin for serial I/O2 goes to high impedance after transfer is completed. When in serial I/O1 (clock-synchronous mode) or in serial I/O2, an external clock is used as synchronous clock, write transmission data to the transmit buffer register or serial I/O2 register, during transfer clock is "H."
Interrupts
The contents of the interrupt request bits do not change immediately after they have been written. After writing to an interrupt request register, execute at least one instruction before performing a BBC or BBS instruction.
A-D Converter
The comparator uses capacitive coupling amplifier whose charge will be lost if the clock frequency is too low. Therefore, make sure that f(XIN) is at least on 500 kHz during an A-D conversion. Do not execute the STP or WIT instruction during an A-D conversion.
Decimal Calculations
* To calculate in decimal notation, set the decimal mode flag (D) to "1", then execute an ADC or SBC instruction. After executing an ADC or SBC instruction, execute at least one instruction before executing a SEC, CLC, or CLD instruction. * In decimal mode, the values of the negative (N), overflow (V), and zero (Z) flags are invalid.
D-A Converter
The accuracy of the D-A converter becomes rapidly poor under the VCC = 4.0 V or less condition; a supply voltage of VCC 4.0 V is recommended. When a D-A converter is not used, set all values of D-Ai conversion registers (i=1, 2) to "0016."
Timers
If a value n (between 0 and 255) is written to a timer latch, the frequency division ratio is 1/(n+1).
Multiplication and Division Instructions
* The index X mode (T) and the decimal mode (D) flags do not affect the MUL and DIV instruction. * The execution of these instructions does not change the contents of the processor status register.
Instruction Execution Time
The instruction execution time is obtained by multiplying the period of the internal clock by the number of cycles needed to execute an instruction. The number of cycles required to execute an instruction is shown in the list of machine instructions. The period of the internal clock is half of the XIN period in highspeed mode. When the ONW function is used in modes other than single-chip mode, the period of the internal clock may be four times that of the XIN.
Ports
The contents of the port direction registers cannot be read. The following cannot be used: * The data transfer instruction (LDA, etc.) * The operation instruction when the index X mode flag (T) is "1" * The instruction with the addressing mode which uses the value of a direction register as an index * The bit-test instruction (BBC or BBS, etc.) to a direction register * The read-modify-write instructions (ROR, CLB, or SEB, etc.) to a direction register. Use instructions such as LDM and STA, etc., to set the port direction registers.
85
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
NOTES ON USAGE Handling of Power Source Pins
In order to avoid a latch-up occurrence, connect a capacitor suitable for high frequencies as bypass capacitor between power source pin (VCC pin) and GND pin (VSS pin), between power source pin (VCC pin) and analog power source input pin (AVSS pin), and between program power source pin (CNVss/VPP) and GND pin for flash memory version when on-board reprogramming is executed. Besides, connect the capacitor to as close as possible. For bypass capacitor which should not be located too far from the pins to be connected, a ceramic capacitor of 0.01 F-0.1 F is recommended.
EPROM version/One Time PROM version/ Flash memory version
The CNVSS pin is connected to the internal memory circuit block by a low-ohmic resistance, since it has the multiplexed function to be a programmable power source pin (VPP pin) as well. To improve the noise reduction, connect a track between CNVSS pin and VSS pin or VCC pin with 1 to 10 k resistance. The mask ROM version track of CNVSS pin has no operational interference even if it is connected to Vss pin or Vcc pin via a resistor.
Erasing of Flash memory version
Set addresses 0100016 to 0FFFF16 as memory area for erasing in the parallel serial I/O mode and the serial I/O mode. If the memory area for erasing is set to mistaken area, the product may be permanently damaged.
DATA REQUIRED FOR MASK ORDERS
The following are necessary when ordering a mask ROM production: 1.Mask ROM Confirmation Form 2.Mark Specification Form 3.Data to be written to ROM, in EPROM form (three identical copies)
DATA REQUIRED FOR One Time PROM PROGRAMMING ORDERS
The following are necessary when ordering a PROM programming service: 1.ROM Programming Confirmation Form 2.Mark Specification Form 3.Data to be programmed to PROM, in EPROM form (three identical copies)
86
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
ELECTRICAL CHARACTERISTICS
Table 28 Absolute maximum ratings Symbol VCC VCC VI VI VI VI VI VI VO VO Pd Topr Tstg Parameter Power source voltageS (Note 1) Power source voltageS (Note 2) Input voltage P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60-P67, P80-P87, VREF Input voltage P70-P77 Input voltage RESET, XIN Input voltage CNVSS (Note 3) Input voltage CNVSS (Note 4) Input voltage CNVSS (Note 5) Output voltage P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60-P67, P80-P87, XOUT Output voltage P70-P77 Power dissipation Operating temperature Storage temperature Conditions Ratings -0.3 to 7.0 -0.3 to 6.5 -0.3 to VCC +0.3 -0.3 to 5.8 -0.3 to VCC +0.3 -0.3 to 7 -0.3 to VCC +0.3 -0.3 to 13 -0.3 to VCC +0.3 -0.3 to 5.8 500 -20 to 85 -40 to 125 Unit V V V V V V V V V V mW C C
All voltages are based on VSS. Output transistors are cut off.
Ta = 25 C
Notes 1: M38867M8A, M38867E8A 2: M38869M8A, M38869MCA, M38869MFA, M38869FFA 3: M38867M8A 4: M38869M8A, M38869MCA, M38869MFA 5: M38867E8A, M38869FFA
87
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 29 Recommended operating conditions (VCC = 2.7 to 5.5 V, VCC = 4.0 to 5.5 V for flash memory version, Ta = -20 to 85 C, unless otherwise noted) Symbol VCC VCC VSS VREF AVSS VIA VIH VIH VIH VIH VIH VIH VIH VIH VIH VIL VIL VIL VIL VIL VIL VIL Parameter Power source voltage (except flash memory version) Power source voltage (flash memory version) Power source voltage Analog reference voltage when A-D converter is used when D-A converter is used f(XIN) 4.1 MHz f(XIN) = 10 MHz Min. 2.7 4.0 4.0 2.0 2.7 0 AVSS 0.8VCC 0.8VCC 0.7VCC 1.4 0.8VCC 0.8VCC 2.0 2.0 0.8VCC 0 0 0 0 0 0 0 VCC VCC 5.5 5.5 5.5 VCC 5.5 VCC 5.5 VCC 0.2VCC 0.3VCC 0.6 0.2VCC 0.8 0.2VCC 0.16VCC Limits Typ. 5.0 5.0 5.0 0 Max. 5.5 5.5 5.5 VCC VCC Unit V V V V V V V V V V V V V V V V V V V V V V
Analog power source voltage A-D converter input voltage AN0-AN7 "H" input voltage P00-P07, P10-P17, P20-P27, P30-P37, P40, P41, P47, P50-P57, P60-P67, P80-P87 "H" input voltage P76, P77 "H" input voltage (when I2C-BUS input level is selected) SDA, SCL "H" input voltage (when SMBUS input level is selected) SDA, SCL "H" input voltage (when CMOS input level is selected) P42-P46, DQ0-DQ7, W, R, S0, S1, A0 "H" input voltage (when CMOS input level is selected) P70-P75 "H" input voltage (when TTL input level is selected) P42-P46, DQ0-DQ7, W, R, S0, S1, A0 (Note) "H" input voltage (when TTL input level is selected) P70-P75 (Note) "H" input voltage RESET, XIN, XCIN, CNVSS "L" input voltage P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60-P67, P70-P77, P80-P87 "L" input voltage (when I2C-BUS input level is selected) SDA, SCL "L" input voltage (when SMBUS input level is selected) SDA, SCL "L" input voltage (when CMOS input level is selected) P42-P46, P70-P75, DQ0-DQ7, W, R, S0, S1, A0 "L" input voltage (when TTL input level is selected) P42-P46, P70-P75, DQ0-DQ7, W, R, S0, S1, A0 (Note) "L" input voltage "L" input voltage RESET, CNVSS XIN, XCIN
Note : When VCC is 4.0 to 5.5 V.
88
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 30 Recommended operating conditions (VCC = 2.7 to 5.5 V, VCC = 4.0 to 5.5 V for flash memory version, Ta = -20 to 85 C, unless otherwise noted) Symbol IOH(peak) IOH(peak) IOL(peak) IOL(peak) IOL(peak) IOH(avg) IOH(avg) IOL(avg) IOL(avg) IOL(avg) "H" total peak output current "H" total peak output current "L" total peak output current "L" total peak output current P24-P27 (Note) Parameter P00-P07, P10-P17, P20-P27, P30-P37, P80-P87 (Note) P40-P47, P50-P57, P60-P67 (Note) P00-P07, P10-P17, P20-P23, P30-P37, P80-P87 (Note) In single-chip mode In memory expansion mode In microprocessor mode Min. Limits Typ. Max. -80 -80 80 80 40 80 -40 -40 40 40 40 40 Unit mA mA mA mA mA mA mA mA mA mA mA mA
"L" total peak output current P40-P47,P50-P57, P60-P67, P70-P77 (Note) "H" total average output current P00-P07, P10-P17, P20-P27, P30-P37, P80-P87 (Note) "H" total average output current P40-P47,P50-P57, P60-P67 (Note) "L" total average output current P00-P07, P10-P17, P20-P23, P30-P37, P80-P87 (Note) In single-chip mode "L" total average output current In memory expansion mode P24-P27 (Note) In microprocessor mode "L" total average output current P40-P47,P50-P57, P60-P67, P70-P77 (Note)
Note : The total output current is the sum of all the currents flowing through all the applicable ports. The total average current is an average value measured over 100 ms. The total peak current is the peak value of all the currents.
89
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 31 Recommended operating conditions (VCC = 2.7 to 5.5 V, VCC = 4.0 to 5.5 V for flash memory version, Ta = -20 to 85 C, unless otherwise noted) Symbol IOH(peak) IOL(peak) "H" peak output current "L" peak output current Parameter P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60-P67, P80-P87 (Note 1) P00-P07, P10-P17, P20-P23, P30-P37, P40-P47, P50-P57, P60-P67, P70-P77, P80-P87 (Note 1) In single-chip mode In memory expansion mode In microprocessor mode P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60-P67, P80-P87 (Note 2) P00-P07, P10-P17, P20-P23, P30-P37, P40-P47, P50-P57, P60-P67, P70-P77, P80-P87 (Note 2) In single-chip mode In memory expansion mode In microprocessor mode Min. Limits Typ. Max. -10 10 20 10 -5 5 15 5 10 4.5 VCC-8 10 10 4.5 VCC-8 32.768 50 Unit mA mA mA mA mA mA mA mA MHz MHz MHz MHz MHz kHz
IOL(peak) IOH(avg) IOL(avg)
"L" peak output current P24-P27 (Note 1) "H" average output current "L" average output current "L" peak output current P24-P27 (Note 2)
IOL(avg)
f(XIN)
f(XCIN)
High-speed mode 4.0 V VCC 5.5 V High-speed mode 2.7 V VCC 4.0 V Main clock input oscillation Middle-speed mode frequency (Note 3) 4.0 V VCC 5.5 V Middle-speed mode 2.7 V VCC 4.0 V (Note 5) Middle-speed mode 2.7 V VCC 4.0 V (Note 5) Sub-clock input oscillation frequency (Notes 3, 4)
Notes 1: The peak output current is the peak current flowing in each port. 2: The average output current IOL(avg), IOH(avg) are average value measured over 100 ms. 3: When the oscillation frequency has a duty cycle of 50%. 4: When using the microcomputer in low-speed mode, set the sub-clock input oscillation frequency on condition that f(XCIN) < f(XIN)/3. 5: When using the timer X/Y, timer 1/2, serial I/O1, serial I/O2, A-D converter, comparator, and PWM, set the main clock input oscillation frequency to the max. 4.5VCC-8 (MHz).
90
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 32 Electrical characteristics (VCC = 2.7 to 5.5 V, VCC = 4.0 to 5.5 V for flash memory version, VSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Limits Symbol Parameter "H" output voltage P00-P07, P10-P17, P20-P27 P30-P37, P40-P47, P50-P57 P60-P67, P80-P87 (Note) "L" output voltage P00-P07, P10-P17, P20-P27 P30-P37, P40-P47, P50-P57 P60-P67, P70-P77, P80-P87 Hysteresis CNTR0, CNTR1, INT0, INT1 INT20-INT40, INT21-INT41 P30-P37 Hysteresis RxD, SCLK1, SIN2, SCLK2 Hysteresis RESET "H" input current P00-P07, P10-P17, P20-P27 P30-P37, P40-P47, P50-P57 P60-P67, P70-P77, P80-P87 "H" input current RESET, CNVSS "H" input current XIN "L" input current P00-P07, P10-P17, P20-P27 P30-P37, P40-P47, P50-P57 P60-P67, P70-P77, P80-P87 "L" input current RESET,CNVSS "L" input current XIN "L" input current P30-P37 (at Pull-up) RAM hold voltage Test conditions IOH = -10 mA VCC = 4.0-5.5 V IOH = -1.0 mA VCC = 2.7-5.5 V IOL = 10 mA VCC = 4.0-5.5 V IOL = 1.6 mA VCC = 2.7-5.5 V Min. VCC-2.0 VCC-1.0 2.0 0.4 Typ. Max. Unit V V V V
VOH
VOL
VT+-VT-
0.4
V V V 5.0 5.0 A A A A A A A A 5.5 V
VT+-VT- VT+-VT- IIH IIH IIH IIL IIL IIL IIL VRAM
0.5 0.5 VI = VCC (Pin floating. Pull-up transistors "off") VI = VCC VI = VCC VI = VSS (Pin floating. Pull-up transistors "off") VI = VSS VI = VSS VI = VSS VCC = 4.0-5.5 V VI = VSS VCC = 2.7-5.5 V When clock stopped
4 -5.0 -5.0 -4 -20 -10 2.0 -60 -120
Note: P00-P03 are measured when the P00-P03 output structure selection bit of the port control register 1 (bit 0 of address 002E16) is "0". P04-P07 are measured when the P04-P07 output structure selection bit of the port control register 1 (bit 1 of address 002E16) is "0". P10-P13 are measured when the P10-P13 output structure selection bit of the port control register 1 (bit 2 of address 002E16) is "0". P14-P17 are measured when the P14-P17 output structure selection bit of the port control register 1 (bit 3 of address 002E16) is "0". P42, P43, P44, and P46 are measured when the P4 output structure selection bit of the port control register 2 (bit 2 of address 002F16) is "0". P45 is measured when the P45/TXD P-channel output disable bit of the UART control register (bit 4 of address 001B16) is "0".
91
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 33 Electrical characteristics (VCC = 2.7 to 5.5 V, VCC = 4.0 to 5.5 V for flash memory version, VSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Limits Symbol Parameter Test conditions High-speed mode f(XIN) = 10 MHz f(XCIN) = 32.768 kHz Output transistors "off" High-speed mode f(XIN) = 8 MHz f(XCIN) = 32.768 kHz Output transistors "off" High-speed mode f(XIN) = 10 MHz (in WIT state) f(XCIN) = 32.768 kHz Output transistors "off" Low-speed mode f(XIN) = stopped f(XCIN) = 32.768 kHz Output transistors "off" Low-speed mode f(XIN) = stopped f(XCIN) = 32.768 kHz (in WIT state) Output transistors "off" Low-speed mode (VCC = 3 V) f(XIN) = stopped f(XCIN) = 32.768 kHz Output transistors "off" Low-speed mode (VCC = 3 V) f(XIN) = stopped f(XCIN) = 32.768 kHz (in WIT state) Output transistors "off" Middle-speed mode f(XIN) = 10 MHz f(XCIN) = stopped Output transistors "off" Middle-speed mode f(XIN) = 10 MHz (in WIT state) f(XCIN) = stopped Output transistors "off" Increment when A-D conversion is executed f(XIN) = 10 MHz All oscillation stopped (in STP state) Output transistors "off" Ta = 25 C Ta = 85 C Min. Typ. 8.0 Max. 15 Unit
mA
6.8
13
mA
1.6
mA
60
200
A
ICC
Power source current
20
40
A
20
55
A
8.0
20.0
A
4.0
7.0
mA
1.5
mA
800 0.1 1.0 10
A A A
92
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 34 A-D converter characteristics (1) (VCC = 2.7 to 5.5 V, VCC = 4.0 to 5.5 V for flash memory version, VREF = 2.0 V to VCC, VSS = AVSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) 10-bit A-D mode (when conversion mode selection bit (bit 7 of address 003816) is "0") Limits Symbol Parameter Test conditions Unit Min. Typ. Max. - Resolution bit 10 - VCC = VREF = 5.0 V Absolute accuracy (excluding quantization error) LSB 4 tCONV Conversion time 2tc(XIN) 61 RLADDER Ladder resistor k 12 35 100 at A-D converter operated VREF = 5.0 V Reference power A 50 150 200 IVREF source input current VREF = 5.0 V at A-D converter stopped A 5 II(AD) A-D port input current A 5.0 Table 35 A-D converter characteristics (2) (VCC = 2.7 to 5.5 V, VCC = 4.0 to 5.5 V for flash memory version, VREF = 2.0 V to VCC, VSS = AVSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) 8-bit A-D mode (when conversion mode selection bit (bit 7 of address 003816) is "1") Symbol - - tCONV RLADDER IVREF II(AD) Parameter Resolution Absolute accuracy (excluding quantization error) Conversion time Ladder resistor at A-D converter operated Reference power source input current at A-D converter stopped A-D port input current Test conditions Limits Min. Typ. Max. 8 2 50 100 200 5 5.0 Unit bit LSB 2tc(XIN) k A A A
VCC = VREF = 5.0 V 12 50 35 150
VREF = 5.0 V VREF = 5.0 V
Table 36 D-A converter characteristics (VCC = 2.7 to 5.5 V, VCC = 4.0 to 5.5 V for flash memory version, VREF = 2.7 V to VCC, VSS = AVSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Symbol - - tsu RO IVREF Resolution Absolute accuracy VCC = 4.0-5.5 V VCC = 2.7-4.0 V 1 2.5 Parameter Test conditions Limits Min. Typ. Max. 8 1.0 2.5 3 4 3.2 Unit Bits % % s k mA
Setting time Output resistor Reference power source input current (Note 1)
Note 1: Using one D-A converter, with the value in the D-A conversion register of the other D-A converter being "0016".
Table 37 Comparator characteristics (VCC = 2.7 to 5.5 V, VCC = 4.0 to 5.5 V for flash memory version, VSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Symbol - TCONV VIA IIA RLADDER CMPREF Absolute accuracy Conversion time Analog input voltage Analog input current Ladder resistor Internal reference voltage External reference input voltage VCC/32 Parameter Test conditions 1LSB = VCC/16 at 10 MHz operating at 8 MHz operating at 4 MHz operating 0 20 40 29VCC /32 VCC Limits Min. Typ. Max. 1/2 2.8 3.5 7 VCC 5.0 50 Unit LSB s s s V A k V V
93
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
TIMING REQUIREMENTS
Table 38 Timing requirements (1) (VCC = 4.0 to 5.5 V, VSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Symbol tW(RESET) tC(XIN) tWH(XIN) tWL(XIN) tC(XCIN) tWH(XCIN) tWL(XCIN) tC(CNTR) tWH(CNTR) tWL(CNTR) tWH(INT) tWL(INT) tC(SCLK1) tWH(SCLK1) tWL(SCLK1) tsu(RxD-SCLK1) th(SCLK1-RxD) tC(SCLK2) tWH(SCLK2) tWL(SCLK2) tsu(SIN2-SCLK2) th(SCLK2-SIN2) Parameter Reset input "L" pulse width Main clock input cycle time Main clock input "H" pulse width Main clock input "L" pulse width Sub-clock input cycle time Sub-clock input "H" pulse width Sub-clock input "L" pulse width CNTR0, CNTR1 input cycle time CNTR0, CNTR1 input "H" pulse width CNTR0, CNTR1 input "L" pulse width INT0, INT1, INT20, INT30, INT40, INT21, INT31, INT41 input "H" pulse width INT0, INT1, INT20, INT30, INT40, INT21, INT31, INT41 input "L" pulse width Serial I/O1 clock input cycle time (Note) Serial I/O1 clock input "H" pulse width (Note) Serial I/O1 clock input "L" pulse width (Note) Serial I/O1 input setup time Serial I/O1 input hold time Serial I/O2 clock input cycle time Serial I/O2 clock input "H" pulse width Serial I/O2 clock input "L" pulse width Serial I/O2 input setup time Serial I/O2 input hold time Limits Min. 2 100 40 40 20 5 5 200 80 80 80 80 800 370 370 220 100 1000 400 400 200 200 Typ. Max. Unit s ns ns ns s s s ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Note : When bit 6 of address 001A16 is "1" (clock synchronous). Divide this value by four when bit 6 of address 001A16 is "0" (UART).
94
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 39 Timing requirements (2) (VCC = 2.7 to 4.0 V, VSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Symbol tW(RESET) tC(XIN) tWH(XIN) tWL(XIN) tC(XCIN) tWH(XCIN) tWL(XCIN) tC(CNTR) tWH(CNTR) tWL(CNTR) tWH(INT) tWL(INT) tC(SCLK1) tWH(SCLK1) tWL(SCLK1) tsu(RxD-SCLK1) th(SCLK1-RxD) tC(SCLK2) tWH(SCLK2) tWL(SCLK2) tsu(SIN2-SCLK2) th(SCLK2-SIN2) Parameter Reset input "L" pulse width Main clock input cycle time Main clock input "H" pulse width Main clock input "L" pulse width Sub-clock input cycle time Sub-clock input "H" pulse width Sub-clock input "L" pulse width CNTR0, CNTR1 input cycle time CNTR0, CNTR1 input "H" pulse width CNTR0, CNTR1 input "L" pulse width INT0, INT1, INT20, INT30, INT40, INT21, INT31, INT41 input "H" pulse width INT0, INT1, INT20, INT30, INT40, INT21, INT31, INT41 input "L" pulse width Serial I/O1 clock input cycle time (Note) Serial I/O1 clock input "H" pulse width (Note) Serial I/O1 clock input "L" pulse width (Note) Serial I/O1 input setup time Serial I/O1 input hold time Serial I/O2 clock input cycle time Serial I/O2 clock input "H" pulse width Serial I/O2 clock input "L" pulse width Serial I/O2 input setup time Serial I/O2 input hold time Limits Min. 2 1000/(4.5VCC-8) 400/(4.5VCC-8) 400/(4.5VCC-8) 20 5 5 500 230 230 230 230 2000 950 950 400 200 2000 950 950 400 300 Typ. Max. Unit s ns ns ns s s s ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Note : When bit 6 of address 001A16 is "1" (clock synchronous). Divide this value by four when bit 6 of address 001A16 is "0" (UART).
95
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 40 Timing requirements for system bus interface (VCC = 4.0 to 5.5 V, VSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Symbol tsu (S-R) tsu (S-W) th (R-S) th (W-S) tsu (A-R) tsu (A-W) th (R-A) th (W-A) tw (R) tw (W) tsu (D-W) th (W-D) Parameter S0, S1 setup time S0, S1 setup time S0, S1 hold time S0, S1 hold time A0 setup time A0 setup time A0 hold time A0 hold time Read pulse width Write pulse width Before write data input setup time After write data input hold time Limits Min. 0 0 0 0 10 10 0 0 120 120 50 0 Typ. Max. Unit ns ns ns ns ns ns ns ns ns ns ns ns
Table 41 Timing requirements for system bus interface (VCC = 2.7 to 4.0 V, VSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Symbol tsu (S-R) tsu (S-W) th (R-S) th (W-S) tsu (A-R) tsu (A-W) th (R-A) th (W-A) tw (R) tw (W) tsu (D-W) th (W-D) Parameter S0, S1 setup time S0, S1 setup time S0, S1 hold time S0, S1 hold time A0 setup time A0 setup time A0 hold time A0 hold time Read pulse width Write pulse width Before write data input setup time After write data input hold time Limits Min. 0 0 0 0 30 30 0 0 250 250 130 0 Typ. Max. Unit ns ns ns ns ns ns ns ns ns ns ns ns
96
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 42 Switching characteristics 1 (VCC = 4.0 to 5.5 V, VSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Symbol tWH (SCLK1) tWL (SCLK1) td (SCLK1-TXD) tV (SCLK1-TXD) tr (SCLK1) tf (SCLK1) tWH (SCLK2) tWL (SCLK2) td (SCLK2-SOUT2) tV (SCLK2-SOUT2) tf (SCLK2) tr (CMOS) tf (CMOS) Parameter Serial I/O1 clock output "H" pulse width Serial I/O1 clock output "L" pulse width Serial I/O1 output delay time (Note 1) Serial I/O1 output valid time (Note 1) Serial I/O1 clock output rising time Serial I/O1 clock output falling time Serial I/O2 clock output "H" pulse width Serial I/O2 clock output "L" pulse width Serial I/O2 output delay time Serial I/O2 output valid time Serial I/O2 clock output falling time CMOS output rising time (Note 2) CMOS output falling time (Note 2) Test conditions Limits Min. Typ. tC(SCLK1)/2-30 tC(SCLK1)/2-30 -30 30 30 tC(SCLK2)/2-160 tC(SCLK2)/2-160 Fig. 84 0 10 10 30 30 30 200 Max. Unit ns ns ns ns ns ns ns ns ns ns ns ns ns
140 Fig. 83
Fig. 83
Notes 1: When the P45/TXD P-channel output disable bit of the UART control register (bit 4 of address 001B16) is "0". 2: The XOUT pin is excluded.
Table 43 Switching characteristics 2 (VCC = 2.7 to 4.0 V, VSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Symbol tWH (SCLK1) tWL (SCLK1) td (SCLK1-TXD) tV (SCLK1-TXD) tr (SCLK1) tf (SCLK1) tWH (SCLK2) tWL (SCLK2) td (SCLK2-SOUT2) tV (SCLK2-SOUT2) tf (SCLK2) tr (CMOS) tf (CMOS) Parameter Serial I/O1 clock output "H" pulse width Serial I/O1 clock output "L" pulse width Serial I/O1 output delay time (Note 1) Serial I/O1 output valid time (Note 1) Serial I/O1 clock output rising time Serial I/O1 clock output falling time Serial I/O2 clock output "H" pulse width Serial I/O2 clock output "L" pulse width Serial I/O2 output delay time Serial I/O2 output valid time Serial I/O2 clock output falling time CMOS output rising time (Note 2) CMOS output falling time (Note 2) Test conditions Limits Typ. Min. tC(SCLK1)/2-50 tC(SCLK1)/2-50 -30 50 50 tC(SCLK2)/2-240 tC(SCLK2)/2-240 Fig. 84 0 20 20 50 50 50 400 Max. Unit ns ns ns ns ns ns ns ns ns ns ns ns ns
Fig. 83
350
Fig. 83
Notes 1: When the P45/TXD P-channel output disable bit of the UART control register (bit 4 of address 001B16) is "0". 2: The XOUT pin is excluded.
97
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 44 Switching characteristics for system bus interface (VCC = 4.0 to 5.5 V, VSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Symbol ta(R-D) tv(R-D) tPLH(R-OBF) Parameter After read data output enable time After read data output disable time After read OBF00, OBF01, OBF10 output propagation time Limits Min. 0 Typ. Max. 80 30 150 Unit ns ns ns
Table 45 Switching characteristics for system bus interface (VCC =2.7 to 4.0 V, VSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Limits Symbol ta(R-D) tv(R-D) tPLH(R-OBF) Parameter After read data output enable time After read data output disable time After read OBF00, OBF01, OBF10 output propagation time Min. 0 Typ. Max. 130 85 300 Unit ns ns ns
98
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 46 Timing requirements in memory expansion mode and microprocessor mode (VCC = 4.0 to 5.5 V, VSS = 0 V, Ta = -20 to 85 C, in high-speed mode, unless otherwise noted) Symbol tsu (ONW-) th (-ONW) tsu (DB-) th (-DB) tsu (ONW-RD), tsu (ONW-WR) th (RD-ONW), th (WR-ONW) tsu (DB-RD) th (RD-DB) Limits Parameter ONW input setup time ONW input hold time Data bus setup time Data bus hold time ONW input setup time ONW input hold time Data bus setup time Data bus hold time Min. -20 -20 50 0 -20 -20 50 0 Typ. Max. Unit ns ns ns ns ns ns ns ns
Table 47 Switching characteristics in memory expansion mode and microprocessor mode (VCC = 4.0 to 5.5 V, VSS = 0 V, Ta = -20 to 85 C, in high-speed mode, unless otherwise noted) Symbol tC() tWH() tWL() td(-AH) td(-AL) tV(-AH) tV(-AL) td(-SYNC) tV(-SYNC) td(-DB) tV(-DB) tWL(RD), tWL(WR) td(AH-RD), td(AH-WR) td(AL-RD), td(AL-WR) tV(RD-AH), tV(WR-AH) tV(RD-AL), tV(WR-AL) td(WR-DB) tV(WR-DB) td(RESET-RESETOUT) tV(-RESETOUT) Parameter clock cycle time clock "H" pulse width clock "L" pulse width AD15-AD8 delay time AD7-AD0 delay time AD15-AD8 valid time AD7-AD0 valid time SYNC delay time SYNC valid time Data bus delay time Data bus valid time RD pulse width, WR pulse width RD pulse width, WR pulse width (When one-wait is valid) AD15-AD8 delay time AD7-AD0 delay time AD15-AD8 valid time AD7-AD0 valid time Data bus delay time Data bus valid time RESETOUT output delay time RESETOUT output valid time (Note) Test conditions Limits Min. tC(XIN)-10 tC(XIN)-10 16 20 5 5 16 5 15 35 40 Typ. 2tC(XIN) Max. Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
2 2 Fig. 83 10 tC(XIN)-10 3tC(XIN)-10 tC(XIN)-35 tC(XIN)-40 2 2 10 0
30
tC(XIN)-16 tC(XIN)-20 5 5 15
30 200 100
Note: The RESETOUT output goes "H" in synchronized with the rise of the clock that is anywhere between a few cycles and 10-several cycles after RESET input goes "H".
99
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
1k
Measurement output pin
Measurement output pin
100pF
100pF
CMOS output
N-channel open-drain output
Fig. 83 Circuit for measuring output switching characteristics (1)
Fig. 84 Circuit for measuring output switching characteristics (2)
100
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Timing diagram in single-chip mode
tC(CNTR) tWH(CNTR) tWL(CNTR) 0.2VCC
CNTR0, CNTR1
0.8VCC
tWH(INT)
tWL(INT) 0.2VCC
INT0,INT1 INT20,INT30,INT40 INT21,INT31,INT41
0.8VCC
tW(RESET)
RESET
0.2VCC
0.8VCC
tC(XIN) tWH(XIN) tWL(XIN) 0.2VCC
XIN
0.8VCC
tC(XCIN) tWH(XCIN) tWL(XCIN) 0.2VCC
XCIN
0.8VCC
tf
tC(SCLK1), tC(SCLK2) tr tWL(SCLK1), tWL(SCLK2) 0.2VCC tsu(RxD-SCLK1), tsu(SIN2-SCLK2) 0.8VCC
tWH(SCLK1), tWH(SCLK2)
SCLK1 SCLK2
th(SCLK1RxD),th(SCLK2SIN2)
RXD SIN2
0.8VCC 0.2VCC td(SCLK1-TXD),td(SCLK2-SOUT2) tv(SCLK1-TXD), tv(SCLK2-SOUT2)
TXD SOUT2
Fig. 85 Timing diagram (1) (in single-chip mode)
101
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Timing diagram in memory expansion mode and microprocessor mode (1)
tC() tWH() tWL()
0.5VCC td(-AH) tv(-AH) 0.5VCC td(-AL) tv(-AL) 0.5VCC td(-SYNC) tv(-SYNC) 0.5VCC td(-WR) tv(-WR)
AD15-AD8
AD7-AD0
SYNC
RD,WR
tSU(ONW-)
0.5VCC th(-ONW)
ONW
0.8VCC 0.2VCC tSU(DB-) th(-DB)
DB0-DB7 (At CPU reading)
td(-DB)
0.8VCC 0.2VCC tv(-DB) 0.5VCC
DB0-DB7 (At CPU writing)
Timing diagram in microprocessor mode RESET
0.5VCC td(RESET- RESETOUT) tv(- RESETOUT) 0.8VCC 0.2VCC
RESETOUT
0.5VCC
Fig. 86 Timing diagram (2) (in memory expansion mode and microprocessor mode)
102
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Timing diagram in memory expansion mode and microprocessor mode (2)
tWL(RD) tWL(WR)
RD,WR
td(AH-RD) td(AH-WR)
0.5VCC
tv(RD-AH) tv(WR-AH)
AD15-AD8
0.5VCC
td(AL-RD) td(AL-WR)
tv(RD-AL) tv(WR-AL)
AD7-AD0
0.5VCC
tsu(ONW-RD) tsu(ONW-WR)
th(RD-ONW) th(WR-ONW)
ONW (At CPU reading) RD
0.8VCC 0.2VCC
0.5VCC
tSU(DB-RD)
th(RD-DB)
DB0-DB7
0.8VCC 0.2VCC
(At CPU writing) WR
td(WR-DB)
0.5VCC
tv(WR-DB)
0.5VCC
DB0-DB7
Fig. 87 Timing diagram (3) (in memory expansion mode and microprocessor mode)
103
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
System bus interface timing diagram Read operation
tsu(A-R) th(R-A)
A0
2.4 (0.8VCC) 0.45 (0.2VCC)
tsu(S-R)
2.4 (0.8VCC) 0.45 (0.2VCC)
th(R-S)
S0,S1
0.45 (0.2VCC)
tw(R)
0.45 (0.2VCC)
R
2.4 (0.8VCC)
0.45 (0.2VCC)
2.4 (0.8VCC) 0.45 (0.2VCC) 2.0 (0.8VCC) 0.8 (0.2VCC)
tv(R-D) tPLH(R-OBF)
DQ0-DQ7
ta(R-D)
2.0 (0.8VCC) 0.8 (0.2VCC)
OBF00,OBF01,OBF10
0.8 (0.2VCC)
Write operation
tsu(A-W) th(W-A)
A0
2.4 (0.8VCC) 0.45 (0.2VCC)
tsu(S-W)
2.4 (0.8VCC) 0.45 (0.2VCC)
th(W-S)
S0,S1
0.45 (0.2VCC)
tw(W)
0.45 (0.2VCC)
W
2.4 (0.8VCC)
0.45 (0.2VCC)
2.4 (0.8VCC) 0.45 (0.2VCC)
th(W-D)
DQ0-DQ7
2.4 (0.8VCC) 0.45 (0.2VCC)
tsu(D-W)
2.4 (0.8VCC) 0.45 (0.2VCC)
Outside of parenthesis : TTL I/O Inside of parenthesis : CMOS I/O
Fig. 88 Timing diagram (4) (system bus interface)
104
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 48 Multi-master I2C-BUS bus line characteristics Standard clock mode High-speed clock mode Symbol tBUF tHD;STA tLOW tR tHD;DAT tHIGH tF tSU;DAT tSU;STA tSU;STO Bus free time Hold time for START condition Hold time for SCL clock = "0" Rising time of both SCL and SDA signals Data hold time Hold time for SCL clock = "1" Falling time of both SCL and SDA signals Data setup time Setup time for repeated START condition Setup time for STOP condition 250 4.7 4.0 0 4.0 300 Parameter Min. 4.7 4.0 4.7 1000 Max. Min. 1.3 0.6 1.3 20+0.1Cb 0 0.6 20+0.1Cb 100 0.6 0.6 300 300 0.9 Max. Unit s s s ns s s ns ns s s
Note: Cb = total capacitance of 1 bus line
SDA
tBUF tLOW tR tF
Sr P
tHD:STA
tsu:STO
SCL
P
S
tHD:STA
tHD:DAT
tHIGH
tsu:DAT
tsu:STA
S : START condition Sr: RESTART condition P : STOP condition
Fig. 89 Timing diagram of multi-master I2C-BUS
105
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PACKAGE OUTLINE 80P6Q-A
EIAJ Package Code LQFP80-P-1212-0.5 HD JEDEC Code - Weight(g) Lead Material Cu Alloy
Plastic 80pin 12!12mm body LQFP
MD
1
60
b2
80
61
l2 Recommended Mount Pad
HE
E
Symbol A A1 A2 b c D E e HD HE L L1 y b2 I2 MD ME
20
41
21
40
A F e L1
b
y
L Detail F
Dimension in Millimeters Min Nom Max 1.7 - - 0.1 0.2 0 1.4 - - 0.13 0.18 0.28 0.105 0.125 0.175 11.9 12.0 12.1 11.9 12.0 12.1 0.5 - - 13.8 14.0 14.2 13.8 14.0 14.2 0.3 0.5 0.7 1.0 - - 0.1 - - 0 10 - 0.225 - - 1.0 - - 12.4 - - 12.4 - -
A2
80D0
EIAJ Package Code - JEDEC Code - Weight(g)
A1
c
Glass seal 80pin QFN
21.00.2
3.32MAX 1.78TYP
41 40
18.40.15 0.8TYP 0.6TYP
64 65
0.8TYP
1.2TYP
25 80 24 1
INDEX
0.5TYP
1.2TYP
106
0.8TYP 12.00.15
15.60.2
ME
D
e
MITSUBISHI MICROCOMPUTERS
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
80P6S-A
EIAJ Package Code QFP80-P-1414-0.65 HD D JEDEC Code Weight(g) 1.11 Lead Material Alloy 42
Plastic 80pin 14!14mm body QFP
MD e
1
60
b2
80
61
I2 Recommended Mount Pad HE Symbol A A1 A2 b c D E e HD HE L L1 x y b2 I2 MD ME Dimension in Millimeters Min Nom Max 3.05 - - 0.1 0.2 0 2.8 - - 0.25 0.3 0.4 0.13 0.15 0.2 13.8 14.0 14.2 13.8 14.0 14.2 0.65 - - 16.5 16.8 17.1 16.5 16.8 17.1 0.4 0.6 0.8 1.4 - - - - 0.13 0.1 - - 0 10 - 0.35 - - - - 1.3 14.6 - - - - 14.6
20
41
E
21
40
A L1
F e y
b
A2
x
M
A1
L Detail F
c
ME
107
REVISION DESCRIPTION LIST
Rev. No. 1.0 2.0 2.1 First Edition The contents of flash memory version were added. All pages; "PRELIMINARY Notice: This is..." eliminated.
3886 GROUP DATA SHEET
Revision Description Rev. date 980216 980716 000114
Page 1; The second "In high-speed mode" of "Power dissipation" eliminated. Page 1; "Memory expansion" is revised. Page 1; Explanation of "" is revised. Page 1; Notes 2 is changed. Page 1; Some words of "APPLICATION" are added. Page 2; Figure 1 and Figure 2 are partly revised. Page 3; Figure 3 is added. Page 7; Figure 5 is partly revised. Page 8; Figure 6 is partly revised. Page 8; Some products are added into Table 3. Page 9; Note into Figure 7 is revised. Page 10; Note into Figure 8 is revised. Page 11; Note into Figure 9 is added. Page 41; Explanation of "I2C Data Shift Register" is partly revised. Page 42; Explanation of "I2C Clock Control Regsiter" is partly revised. Page 42; Note 1 into Table 10 is partly revised. Page 50; (6) and (7) of "Precaution when using multi-master I2C BUS interface" are added. Page 51; Figure 48 is partly revised. Page 56; Explanation of "RESET CIRCUIT" is partly revised. Page 56; Note into Figure 55 is revised. Page 60; Figure 61 is partly revised. Page 61; Explanation of "PROCESSOR MODE" is partly revised. Page 61; Explanation into Figure 62 is eliminated partly. Page 61; Note into Figure 63 is revised. Page 66; Figure 66 is partly revised.
(1/2)
REVISION DESCRIPTION LIST
Rev. No. 2.1
3886 GROUP DATA SHEET
Revision Description Rev. date 000114
Page 73; Minimum limits of VPPH into Table 22 is revised. Page 74; Figure 72 is partly revised. Page 81; Explanation of "Flash memory mode 3 (CPU reprogramming mode)" is added. Page 81; Note into Figure 79 is eliminated partly. Page 82; "CPU reprogramming mode operation procedure" is eliminated partly. Page 82; Figure 81 is partly revised. Page 86; Explanation of "Handling of Power Source Pins" is added. Page 86; Explanation of "Erasing of Flash memory version" is added. Page 87; Parameter into Table 28 is partly revised. Page 88; Parameter into Table 29 is partly revised. *Mask ROM confirmation forms are eliminated. V Refer to the "Mitsubishi MCU Technical Information" Homepage (http://www.infomicom. mesc.co.jp/indexe/htm). [38000 Series Mask ROM Confirmation Forms] *ROM programming confirmation form is eliminated. V Refer to the "Mitsubishi MCU Technical Information" Homepage (http://www.infomicom. mesc.co.jp/indexe/htm). [38000 Series Mask ROM Confirmation Forms] *Mark specification form is eliminated. V Refer to the "Mitsubishi MCU Technical Information" Homepage (http://www.infomicom. mesc.co.jp/indexe/htm). [38000 Series Mask ROM Confirmation Forms ROM Ordering Method Mark Specification Forms] Page 107; Package outline for 80P6S-A is added.
(2/2)
Keep safety first in your circuit designs!
* Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
* * * These materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party. Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Mitsubishi Electric Corporation by various means, including the Mitsubishi Semiconductor home page (http://www.mitsubishichips.com). When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for further details on these materials or the products contained therein.
* *
* *
*
(c) 2000 MITSUBISHI ELECTRIC CORP. H-LF492-A KI-0001 Printed in Japan (ROD) II New publication, effective Jan. 2000. Specifications subject to change without notice.

▲Up To Search▲

Price & Availability of M38869FC-XXXHP

	To Download M38869FC-XXXHP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .